my 2500+ run at 3200+ on nf7-s at 1.775vcore. Try increase your vcore

I use 1.8vcore for xp. Try to raise it up to 1.8

I know, but mine stable at 1.8Vcore for xp but currently at 1.775 for 2000 (sejuk sikit)

Connot brag on cpu temp coz using crappy hsf.
Case 40 CPU 63(load)
Case 33 CPU 49-56(idle)

After i refer your rig, i think the main prob to oc your proc is your ram. Dun think that you can reach 200fsb with that ram.

hmm...currently waiting for jet7+ bought from Vtec(rock). anyway dun want to waste much money for this outdated system .

thank for the suggestion .

hehehe...it seem quite a number of people cannot afford tt big water including me.

This post has been edited by LarharT: Nov 12 2005, 10:26 PM

Anyway didn't prefer water cooling. It's seem so annoying to setup and maintain ( or it just me being so lazy )

This post has been edited by LarharT: Nov 12 2005, 10:36 PM

above ddr400 is ddr2, cannot fit your current mobo. Just get kvr or hyperX and not apacer ram.

kinda noob over here. want to know the function of this 'Solution for low overclock in Windows XP SP2'? what does it do?

thanks man. should try this too

sorry for late update.

before
axp2500+ at 2.2g
Vcore at 1.8
temp idle at 50
temp full load at 66

after
axp2500+ at 2.2g
Vcore at 1.725
temp idle at 50
temp full load at 60

using
nf7-s v2.0
512 hyperX

thanks man for the guide

This post has been edited by LarharT: Dec 6 2005, 08:31 AM

yup, less heat and at least didn't have to buy any hsf anymore.

1) i think can at least up to 2.3g. it up to you want to flash it or not. the nf7-s default bios is already good to oc.
2) you should check it on your own. but your hsf . tak payah la oc lebih dari 2v. 1.8volt pun dah cukup panas.
3)sometimes it is required to increase the agpvoltage to avoid artifacts.

if you set the max vcore, then i think we can do some cooking(fried chiken maybe ).

just set your fsb to 200 and vcore to 1.8v and buy new hsf. if you want to oc more , may be it'll effect you ram. corsiar vs . pi beli hypeerX ka bt-d43 ka, baru boleh oc sedap sikit .

cannot set your cpu at 200*11.5 @1.8v?
FYI, rising the voltage is to make your oc system stable in OS. i don't see whether is it related to performance but increasing your voltage more than you should be, you will only get heat .

mobile proc on 1.9V. it seem too high for me.

follow gr2000 advice to check the stepping.

proper way to put thermal grease is to use card(any card like prepaid cad). apply the the thermal grease( besar sebutir beras aja) on the cpu surface, using the card *ratakan the grease. sorry no pic include.

arafat, you can refer to this link

http://www.arcticsilver.com/arctic_silver_instructions.htm

however instead using razor, like the web suggested, you can also use card as i say before.

This post has been edited by LarharT: Jan 17 2006, 06:47 PM

if your proc is unlocked, try to decrease the multiplier, if the multiplier can be decrease, that's mean your proc is unlock.

your v-core also need to be increase. try and error increasing the voltage until you reach the stable voltage. but beware if you're using stock hsf, you might encounter with heat problem

you might be right, my 2500+ multiplier is 11(unfortunately locked ).

V-dimm is for memory right(lupa lak)? if so may be should be increase since your fsb exeed 200mHz.

but your proc can easily hit 2.2g by setting fsb(200)xmultiplier(11) at vcore 1.8volt.

This post has been edited by LarharT: Feb 2 2006, 01:59 PM