isn't your barton a locked one? or unlocked?

it's unlocked if the multiplier can be changed right? my one have a multiplier that can be changed.

No, I really don't know why it fails the very first time I put my CPU (yeah, straight away do mild o/cing hahaha). This is 2600+ running on 12.5x166 on KT333 (yeah fsb 200 will kill my hdd hehe). I tested with 12.5x200 yesterday, it boots nicely, but 58C idle!! (Me on stock hsf). Anyways, I think we can really trust the stepping in DTR, unlike normal desktop which same stepping does not give same o/c. I wonder how good soulfly's 2800+ will be. I hope it cracks 2.8GHz with air cooling hahahah!

its time to tukar board laioz...
wah..idle temp very bad huh."try fitting ur heatsink again.." it wont go that high one lar even when u oc...to further oc..make sure temp under 50'c ..

12.5 x 200mhz=2500Mhz great result! at wat voltage?

ehh...my proc boot up at 2900Mhz ok ! haha..using 2volts le..air cooling !

u relli haf the guts to do it...2volts on air...i bet the 2.9 gig is anything but stable as the highest ppl gone wif a barton is 2.7g stable runing phase change cooling...and even tat oso their hdd corrupt after a certain period running on those settings

hehe..only for a screenshot mah ..."thank god" its still alive!

this may sound silly but i really don't understand, how does the hdd corrupt at those proc speeds?
data corrupt or the hdd really kiao?

I'm on stock cooling. So, the temperature is normal. 2500MHz was at 1.65Vcore. Just tried only, didn't really have time to test hehe.

This post has been edited by davidletterboyz: Mar 5 2005, 12:11 AM

the overclock isn't too stable running on daily use resulting to corruption of data to the hdd....it's pretty normal for hardwares to act weird when u ran them way out of their specs

Damn! 12.5x200MHz fails at 1.65Vcore after 18mins of priming (small FFTs)!!!! This is a bad indication? LOL KT333 with stock cooling haha. Full load tempt was 58C.

Now priming at 1.675Vcore. Temp is 59C. Hope it's going well.

EDIT: Failed after 28mins.

This post has been edited by davidletterboyz: Mar 5 2005, 01:31 AM

dont rush le..u might damage ur proc like tat (bcos temp)...get better cooling..or fit another big a** fan on the heatsink.

my proc need 1.725v for 2500mhz (at first) ...now after burning in 1.675v..

tone.

Hehe, high temp = burns faster LOL. Ok, me got myself a cheap brandless HSF. Now going to shop to buy sandpapers.

any test using sisoft sandra?

come come all clock it, post it and rank it!! join the list!

i'm getting my 2.5 gig stable then i'll be posting again. =]

even my mobile barton needs 1.75v to run stable, and temp must be lower than 50'C, if not prime error.

my proc at its limit using a chapalang icute...the psu might be the bottleneck but then the proc might relli be at its limit too...will try out again after i got my hand on my enlight next week


Attached File(s)
 2.37gig_1.95v.bmp ( 1.5mb ) Number of downloads: 30

http://forum.lowyat.net/index.php?act=Atta...e=post&id=49771

12.5x200MHz @ 1.675Vcore.

This post has been edited by davidletterboyz: Mar 10 2005, 02:17 AM

very good stepping i see

just got my DTR Barton AQZEA 0332MPMW from gengstapo. will try later when receive back my other DFI UI.

Didn't have time to test it further. 10.5x250@1.80Vcore was OK until 52mins!



Attached thumbnail(s)

pump 1.825v ..go david ! go david!