Sempron64 2500+ , 2800+ OC tests
|
|
 Nov 14 2005, 03:40 PM
Return to original view | Post
#1
|
 
Senior Member
2,778 posts Joined: Jan 2003 From: about:robots 
|
just got my sempron yesterday. no time to play with it yet.
2800+ DFI infinity nf4x 1024 D43 MSI 6600GT diamond i've never oc'ing any amd so far. how far u guys think i can go with stock cooling? btw its said that the pci is locked with processor fsb, that means if i change the fsb my pci clock also will change? |
|
|
|
|
|
Nov 15 2005, 09:24 AM
Return to original view | Post
#2
|
|
Senior Member
2,778 posts Joined: Jan 2003 From: about:robots
|
i got delayed booting into windows. just before the logon screen, right after the windows logo with the blue bar. it goes black for a few seconds. why is that happening?
|
|
|
Nov 15 2005, 09:40 AM
Return to original view | Post
#3
|
|
Senior Member
2,778 posts Joined: Jan 2003 From: about:robots
|
QUOTE(antonio_zth @ Nov 15 2005, 09:32 AM)  :P:P:P:P....try setting back all to factory defaults then try and overclock back again...if while in stock settings also litdat it means corruptions has occured...   stock setting also like that    btw what is HT multiplier for? This post has been edited by ayiesz: Nov 15 2005, 10:08 AM |
|
|
Nov 15 2005, 11:12 AM
Return to original view | Post
#4
|
|
Senior Member
2,778 posts Joined: Jan 2003 From: about:robots
|
if i'm running 270 x 8 can just let it stick at 4x HT or should i lower it to 3xHT?
|
|
|
Nov 17 2005, 09:27 AM
Return to original view | Post
#5
|
|
Senior Member
2,778 posts Joined: Jan 2003 From: about:robots
|
maybe its true that s754 is set to 800, coz by default the multiplier is set at 4x, so 200x4=800. unless by default its 5x, then it should be 1000.
now im running 280 with 3x HT multiplier. still above 800 but passed 4 hours of prime with blend setting. cpu:ram is 1:0.7 this is just to test how high i can go with the fsb. will change the multiplier and divider later. idle temp is 40, load at 51 my question is, should i go for high fsb, high HTT or tight ram timing? This post has been edited by ayiesz: Nov 17 2005, 09:29 AM Attached thumbnail(s) 
|
|
|
Nov 18 2005, 09:50 AM
Return to original view | Post
#6
|
|
Senior Member
2,778 posts Joined: Jan 2003 From: about:robots
|
here's mine
running on stock cooling idle 39'C load 54'C FSB:DDR 1:0.6 HT 3x about the ram, how to calculate it actually? i'm confused a bit. Attached thumbnail(s) 
|
|
|
|
|
|
Nov 18 2005, 02:36 PM
Return to original view | Post
#7
|
|
Senior Member
2,778 posts Joined: Jan 2003 From: about:robots
|
so now does that means my ram is running on 200MHz or 180MHz
thanks  |
|
|
Nov 22 2005, 05:52 PM
Return to original view | Post
#8
|
|
Senior Member
2,778 posts Joined: Jan 2003 From: about:robots
|
do i need to turn off CnQ features or can i leave it on? rite now its off, just want to know if its ok if i turn it on
|
|
|
Dec 7 2005, 01:44 AM
Return to original view | Post
#9
|
|
Senior Member
2,778 posts Joined: Jan 2003 From: about:robots
|
QUOTE(Cyclone87 @ Dec 6 2005, 08:01 PM) Try this setting any help for tp-d43?HTT - 337 HTT ratio - 3x or 2.5x Ram Divider : 133% with 1T timing. K8 dont like 2T PCIe clock : 101mhz Chipset voltage : As low as posible. If high , it will generate heat and cause u unstable when under high HTT. Try to Oc with 1 stick of ram. If u on two stick...use 100% divider and see how high u can go. If you on Hynix chipset ram, like DT-D43,BT-D43,BT-J. Row cycle time~ 11-12 Row refresh cycle time ~ 11-13 |
| Change to: |  0.0312sec
 0.41
 7 queries
 GZIP Disabled
Time is now: 1st December 2025 - 04:45 AM |
Quote