32 Byte Granularity - Disable(8 Bursts)

put 4bursts....
ur ram voltage wil be lower as 2.8 or 2.9

last times i oso face tis problem n run my tccd at 3.3v
flash to 618-3 bios n no hav 8bursts for me...so i choose 4 bursts n my ram vdimm drop til 2.9v@300fsb

may i know wat diffrent between tcc5 n tccd??
timing??

http://valid.x86-secret.com/show_oc?id=27814
2.5-4-4-8@321*9@3.0v@1:1

but after i burn in for few day...now can make it at 2.5-4-3-6 2.9v 321@1:1

no time to benmark jor...kinda lazy now...hahaha

no lah...fx-57 more power full
so u fast fast get 1 unit sandy loh...

cos i wanna change my ram soon...i wanna find a tccd ram tat can do at ddr600@2-2-2-5@1:1

but ur ram oso not bad, can do at 2.5-4-3-6@ddr600

memtest86 wit 12hours then stop for a while...if u got a good cooling then no need to stop... n i found prime95 is a good software to burn in ur pc...

cos every time i open 2(means run prime95 two at the same times) n run fft at 1024mb.

290*10 wil fail at 1h16min at the 1st... mb my cooling no really good...
my ram d@mn hot

This post has been edited by kelvin_hata: Aug 24 2005, 11:40 PM

i argee too...cos my bh-5@2-2-2-5@1:1@3.7v can prime stable for 3hours at 265*11..without any problem

ya...tat y i need to find a good tccd can run at 2-2-2-5
i think onli geil can do it...but the price

babyelf gem...mind send to me n let me try the speed

1. babyelf - 8125 PTS - Gskill LE TCCD @ 7-3-3-2.5 @ @ 302 MHZ @ 1T @ 2.73 VDIMM

i didt set all...onli set the timing...cos last time i buy all stuff, n i cant find gskill ram in lyn tat y i tempory use my old bh-5 to run 1st...

last times buy tis baby at rm400 onli 256 corsair 3200 rev1.1, on b'cos run at single channel n didt do any benmark, jus use tat ram to burn in my proc

but ur superpi using sandy vy fast wat...abt 27sec finish 1mb jor...

cannot run at ???
Row to Row delay (Trrd) - 02 Bus Clocks
Write recovery time (Twr) - 02 Bus Clocks
Write to Read delay (Twtr) - 02 Bus Clocks
Read to Write delay (Trwt) - 02 Bus Clocks

dunno loh...cos i can run 3dmark wit tis setting...if i put 3,3,2,3 or 3,2,2,3 got problem... but put it 2,2,2,2 then no problem jor

i oso pelik
mb u can try lah

hmm...here my old bh-5 run at 2-2-2-7@267@3.7v@1:1@1t



This post has been edited by kelvin_hata: Aug 26 2005, 12:37 AM


Attached thumbnail(s)

hmm...my sandy wit tccd oredi run 3day non stop run BT.
running at 2.5-4-3-6 1t@3.0v@321*9

soulfly:- how abt ur pc uptimes wen running 300fsb, u got blow any fan to the ram? cos my ram d@mn hot, 42'c
this normal or too hot for tccd??