Dont know whether is it a suitable place to post or not ..

Anything idea what cause failed ?

2x512MB Corsair TwinX DDR400 v1.4, running at 270MHz, 2.5-4-3-7,1T, 3.2v

memtest run >7hours same setting with3.0v no error.
but in window i need to adjust to 3.2v



here is my tweaker setting :

Which one more realible ? or should i said more trusted ?
Prime95 or SP2004 ?
The Prime95 failed but SP2004 still running no error yet..

This post has been edited by ahpaul82: Aug 30 2005, 05:16 PM

voltage too high?
but i think mine's TCCD is not as good as you guy one leh..


ok
i will try lower the voltage and kianwee setting .

Im using Blend Test to test my RAM stability.

Thanks for the kianwee, soulfly and pcmoddingmy's sugguestion.
I will give it a try. Thanks a lot.

I think the max speed for my Corsair RAM can run is 275MHz only .
last time did a test with my Winchester and can run >8hours no problem but with kinda loose timing. i think is 2.5-4-4-8,1T, 3.2v.
I forgot how im able to do that timing last time.. >>>



Now don't think about RAM first,
test my processor how high can go but with low voltage ..

That time forgot to take the A64 Tweaker screen ..

oh, mean you recommend custom setting than perset setting to test the RAM is it ?

somemore need to run 2days only can say system 100% stable ar ?

i stop test the RAM already.
now finding the max HTT my Venice can go . last time need >1.600v only can do 285HTT, after few days burn in, now my Venice able to do 285HTT with 1.525v, although i know is still quite high vcore, but compare last time, still ok la . (using stock fan and divider of coz ) i hope not my board holding me back .

As my fren told me, the 2x512MB Corsair TwinX PC3200 is using TCCD ramchip (default timing is 3-3-3-8), but i think not optimize as those high performance ram lor.. if not that ram can sell at high performance RAM already. if im not mistaken the highest MHz i achieve on last time is 2.5-4-4-8, 1T, 3.2v . highest than 275MHz memtest got thousand errors in test5
that time i think all RAM advanced setting i set to default or auto, just change the 1T and Max Async Latency to 7 and Read preable to 5. Didnt test CL3 in fact, i cannot realy remember.

For your information, My 2x512MB Corsair TwinX batch are 0512053-7. mean is year05 week 12 product one . Any comment on it ?

I having weird problem for my Venice... more detail refer to Venice Overclocking and Discussion Thread

This post has been edited by ahpaul82: Aug 31 2005, 11:31 PM

Any wrong setting here?
memtest #5 no error so far but once in window try run Prime95 will failed within 1min
How to overcome this ?

after follow some guide and suggestion from you guys,
now my TCCD able to run at 270MHz ,2.5-4-3-7, 1T, 2.7v
last time need 3.0v...

I wonder is it tighter DRAM setting is suitable for TCCD ?
I realiased one thing is that, the RAM run more hotter than when i set to 3.2v !!!




Genic BIOS Setting :
CPU Frequency = 270MHz
Hammer Fid Control = x9
HT Frequency = 3x
HT Width = Up 16 Down 16
PCIE Clock = 100MHz
AMD K8 Cool & Quiet = Disabled
DDR Voltage Contorl = 2.7v
Chp Voltage Contorl = 1.7v
CPU Voltage Control = 1.500v

DRAM Configuration :
Timing Mode = Manual
Memclock Mode = Update
Memclock index value (MHz) = 200MHz CPU:DDR 1:1
Tcl = 2.5
Tras = 7T
Trcd = 4T
Trp = 3T
Trrd = 2T
Trc = 10T
Trfc = 16T
Twr = 2 bus clock
Twtr = 2 bus clock
Trwt = 2 bus clock
Tref = Auto
Twcl = 1 Mem clock after CAS#
DDR Cut Driving = Auto
DDR DQ Drive Strength = Auto
Bottom of 32bit [31:24] IO = E0
1T/2T Memory Timing = 1T
Read Preamble Value = 6ns
Async Latency Value = 8ns
Dynamic Idle Cycle Counter = 256cycle
DRAM Bank Interleaving - Enabled
Burst Length = 8beats
Enable ALL DIMM Clock = Enabled
S/W Memory Hole Remapping = Disabled
H/W Memory Hole Remapping = Disabled
MTRR Mapping Mode = Continuous
DRAM ECC Feature Control = Disabled

Will post my A64 tweaker tonight .

FYI, My current spec are :
Processor - AMD64 3000+ Venice E3 (s939)
Mobo : DFI NF4 DAGF (BIOS-801)
RAM : 2x512MB Corsair TwinX XMS PC3200 v1.4
Graphic Card - PCI S3 4M
HDD : WD 40GB 8MB
Optical Drive : ASUS 52x CD-ROM
PSU : OCZ Modstream 520W PSU
Window XP PRO SP2 with all critical updated.

I saw that thread too yesterday,
in fact i have to satisfy with my board, should said cannot expect too much
coz my board is budget mobo only ..

normally i will run full test after 1hours of test#5 and #8 each.
but then i think now suitable me to find max HTT my processor can go first.

i expect too much for my RAM la .. haha

Wish me luck

Hopefully This Thread can help you

Finally owned a DFI NF4 SLI-D, although a bit late

using 2 x 512MB Corsair XMS3200 v1.4

should i go further?

Can anyone explain to me why memtest #7 can failed but passed through #5 and #8 ?

anyone ?

I saw that thread too,
but wonder TCCD can overheated so easily ?
vdimm only 2.8v.
havent tested in Window yet.

Anyone can anwser me why my Corsair only able run at CL2, but not CL2.5 and CL3 ???
mine is XMS3200 v1.4 (2x512MB)
RAM spoil or what ?

this pair able to do CL2.5-4-3-7 at >250MHz last time one woh... HERE
now just don't want to do CL2.5 ...
looks like the pair need to RMA already...

*abit out of topic*
the rated timing of that RAM is 3.3.3.8.
ermm.. where you send for RMA ? to USA ?
coz the RAM is bought from Malaysia Corsair Official Supplier Cudo lor ..
so i think i will just pass to them.

he is running 1.6vcore.
and remember, CPU-Z alwaz show under-volt for Processor.

The pair 2x512MB XMS3200 v1.4 finally sent for warranty already.
have to wait until mid of next month only able to get it.

Hopefully is a not bad pair.

I got back my XMS3200 from warranty last week,
is a XMS3200v6.1,
0516013-0
should be UTT chips
no time to test yet

in fact, i did open a bit the heatspreader and check and confirm is using UTT.
now more interested to play 2X1GB RAM

This post has been edited by ahpaul82: May 27 2006, 09:04 AM

hehe, nice found.

let me settle down the 2x1GB KVR UCCC first,
then i will be bck to this XMS version6.1 RAM