Barbs got plenty at Ace Hardware lar. Nice 1's too. got 3/8, 1/2 oso got. Even got plastic barbs. T joints, L joints, everything got man. Ace HArdware rox.

PVC glue is plumber's glue. The normal pvc pipe glue from hardware store. I use that too.

Ikano Ace. Got season 1. Sumtimes wat oso dont haf. But currently a lot of that stuff.

Y so susah buy from overseas? Here oso got a really good passive cooler in the form of the Zalman Reserator. Any problems can RMA sumore.

Can order 1 IIRC. Or mebe it was Eheim I read about. Try google n c?

A big thank u to dinster. Now we dont hafta worry bout our WC supplies. Coz LYP is like a desert in terms of water cooling.

Kakaka. Sniper finally installed everything. 7 months later..........


Anyway, here's my new set up now guys. I had to take my gfx card out of the water loop. Any of u seen waterblocks for the 7950GX2? I've been yahooing n googling like mad n cant find any. All I found was the Coollit System that comes with the Alienware Quad SLi 7900GX2.






Now u c my prob? The gap between the cards is really narrow. Cannot fit universal gfx waterblocks.

Holy crapperoo Sniper, ure luck has really been awesomely bad of late. Was water still circulating in the loop when u got back? Coz the MCP350 is very sensitive to running dry. The manual says DO NOT RUN DRY. If it was running on dry loop then u better gif the pump a good check too.

That 3 barb block u posted looks extremely deeeeeeeeeeeeeeeeliciouso. Get that n polish it to a mirror shine. OMG! I can imagine that super bling block. What brand is it BTW?

My damn MCP350 pump is acting up again. Blardy hell. Stupid Laing says it's an industrial grade pump n blah blah blah with a MTBF of 50000 hours. BOLLOCKS to that!

I use my rig for about 10 hours a day for the past 8 months with the new pump that Corsair sent back to me after the 1st died. That's 240 days x 10 hours a day which comes to only 2400 hours usage time n it's already giving me startup probs.

Sumtimes when I boot up the pump doesn't startup n I hafta gif it a few taps from under my case n then only the pump starts up. Really fed up lar.

This post has been edited by ianho: Jun 28 2006, 10:46 PM

The 1 I'm using now is the new revision with the RPM sensor. Corsair sent back a brand new rev.2 pump to me but I'm going tru teh same thing as my 1st pump again.

haha. Read until I pening d. The prob is Corsair's RMA took 3+ months the last time. Blardy ridiculous! So far it's been usable still. After the few taps I gave it the other day, it's starting up nicely so far. Haiz.............. if it dies again, I think I'll just get an Eheim 1046 or 1048. Those shud b nuclear proof since it's made to withstand sucking in all that fishcrap n also saltwater usage which means it can take deposit build up. Dedicated PC pumps like the DDC all like pondan, must use clean water, cannot use UV die, cannot use tap water, recommended to use only Corsair coolant n all that shite.

Very, very cheap oni lar. The 3/8" ID, 1/2" OD tubes cost oni about 90 sen a foot. Much, much better than the Aeroplane tubes.

The Eheim 1046 is really really puny man. Y not get the 1048 for only rm50 more?

Mineral water? Mati lor the components. With all those minerals n salts in there sure corrode everything.