Same actually

owh ok...thanks...
btw do u guys noe the simplest n cheapest way to build a heatercore fan shroud?
sorry if i post in wrong topic...

This post has been edited by Susaiput: Jun 3 2009, 06:31 PM

1st show us some photos of ur heatercore...

Yesterday, I've changed my Apogee GT to GTZ and guess what, there's no difference in temp Even if it does, it's more like 1-2C difference. Not bad for the extra RM160 I paid for it?

bro, one question here (noob question), if change the rad can ar see different result? i mean use current WC set up but use with better rad.

@atomik...im sure theres a change of temp...but maybe not much...depending on the rad...

@IcEMoCHa
heres the pic of my heatercore...any suggestions?

---

Added on June 4, 2009, 9:07 pm




This post has been edited by Susaiput: Jun 4 2009, 09:08 PM

Eeeh on load/idle?
Could be also due to ambient or stuck processor sensor
But then again GT to GTZ temp difference should not be huge also
Maybe i7 see bigger difference
Hmmm look at it,think you pay the premium for bragging right/look/easier mounting lor

Yes, you would be able to see difference. The trick is always about how fast/good you can cool the water running in the loop. There's a limit on what the water block can do.

Yes, it's about the same and at most 1-2C difference. CPU WB has been evolving a lot and those reviews always puts it nicely but from my experience in changing blocks, it doesn't really yield a lot of difference A little regret for paying so much more for the GTZ but then again, I get i7 bracket which I can use in future It might be the processor thermal sensor too like you said because I've owned quite a number of Wolfdale and all of them gave different temps. No ideas what Intel is doing

woah.. thats big.. the fins kinda dense.. for the shrouds u can use a wooden plank cut 4 square holes on it and stick it to ur heatercore then screw 4 fans on it.. hmm..

@IcEMoCHa
its not that big actually...it cant fit more than 1x12cm fan...if i use a metal shroud made from sheet metal...how do i stick the metal to the heater core?
at first i thought of buying a heater core i found earlier which have perfect size for mounting 2x12cm fans...but the conditon of the item is very bad..if not... 4xFFB1212EHE...

This post has been edited by Susaiput: Jun 6 2009, 01:14 AM

i see.. what is the dimension of it anyway?... actually u need more static pressure than airflow as the fins are dense(not sure as photo too small).. possible to fit 2x8cm fans?..

This post has been edited by IcEMoCHa: Jun 6 2009, 11:53 AM

Susaiput, u need a fan with serious static pressure, the fin are rather dense.... not to mention some serious noise maker..

may be u should consider making an enclosure to seal the fan and heater core together to cut the noise.

@IcEMoCHa
i think if 2x8 can fit...



@LExus65
ermmm...static pressure?im noob in this...can u xplain in more detail pls...currently ive got 2xffb1212ehe which i planned to use on the heatercore...

is it statice pressure increase = cfm decrease?

i tot of making a full fan shroud...cuz i saw a tutorial vid on the internet on performance shroud made for 2x12cm fans...

static pressure means the pushing force.. if u use high cfm fans with low pressure to blow at ur heatercore with dense fins, then only little amount of air will go thru therefore reducing the cooling performance.. usually smaller fans with high cfm have more static pressure than big fans with huge cfm..

hai guys

is it rm350 is valueable for CoolIT Domino A.L.C. watercooling system ?

hi all,

wanna ask is it ok if i put the fan for WC like that....cause the space at behind not enough due to block by mobo....

I don't see anything wrong with that setup as I used to have my dual radiator on top of my Cosmos with 2 fans blowing out from the casing.

hmm.. having rads higher than ur res is it harder to bleed the air?..

I think it is more or less the same (since I have it in front of my Lian Li now). After a quick while and things would be fine Btw, I'm running on distilled water only, no coolant.

HAIZ...i'm facing a new problem again...i install this WC yesterday at 3pm today at 10am my screen suddenly freeze....and can't boot...after i checked and found the liquid from pump to cpu got no water....so i suspect the pump might be broken...anyway the pump can be repair DIY, i tried call the seller but didn't pick up the hp and pm him as well....