so what ur think about this type of WC for my amd phenom2 X3 720BE

Swiftech Apogee GT

Nirox P2800 Pre-modded

Swiftech MCR220-QP

Swiftech MCRES Micro


or i want buy cheap, old TT Air besar 735 then modified it?

so how?

since u r using same proc with me.im suggesting u using TEC coolit domino ALC.
using Push n pull method the on the rad,my OC x3 720 BE 3.6ghz full load 40c..idle only 33C
sumore this wc is cheap!

That Apogee GT is a decent block The problem with using Nirox pumps are that it runs on AC power.

bro can list down what casing and plus all coolen that u use??

where can i get the set?

glad ur happy with ALC. mine is performing well and need to fork out money from wallet. mcr220. haha

CoolIT Domino ALC is just a WC kit.... There's no TECs on them.... The onli one that has TECs are CoolIT Freezone Elite.... That's for CPU that is....

is it TEC using peltier plate?

TEC = peltier lo

Domino ALC are just plain WC just like wat aura said...

haha.. which tube are good 3/8" or 1/2"?

There's no good or bad... 3/8" is smaller... 1/2" is the biggest u can find in terms of inner diameter....

if u wanna know what's the best tubes, then it must be Tygons.... Expensive but best quality....

lol i know what are the smaller or bigger tube...wrong question..tygon? hmm..

bigger tubes got higher flowrate lo, smaller tube smaller flowrate, nowadays block design have minimal impact on the tube size ady, old block show more significant difference, i using 7/16 ID on 1/2OD barb, holding tight and feel safer for me though but super troublesome when setting up the tubings...

so need to use small rate pump for small tube..but also depend on the pump..rite? got centrifugal..or positive displacement

not related to the pump, smallerr tube higher restriction, bigger tube lower restriction, so u will get higher flowrate for the waterblock if u use bigger tubing size, ntg to do with the pump, the pump deliver what its got, depends on the restriction and setup of ur loop for the flowrate.

So smaller tubing can use powerful pump like the D4, D5 as well...

This post has been edited by lichyetan: May 2 2009, 08:19 PM

those got Radbox and mcr220 pls find me. i want make my H20 120 compact to H220 220 compact.

err. how to use the peltier plate? is it just put it between the the upper surface of proc and cpu block (sandwich between proc and the cpu block)

This post has been edited by atomik: May 3 2009, 01:11 AM

The peltier plate has what u called a cold side and a hot side.... Normally the cold side will face the proc and the hot side is to the WB....

http://forum.lowyat.net/topic/931986

http://forum.lowyat.net/topic/433683

between two link given have different peltier plate. which one is prefer to use?
the more i doing research, more i got alot of question.

not recommed to put on top of proc, very difficult to work with...

aura, not only freezone is TEC cooled lol

If u wanna include the Boreas and the Chiller that is.... I'm onli comparing between CPU coolers and not overall and GC coolers....

This post has been edited by Aura: May 4 2009, 12:21 PM

Hi to everyone. I am planning to watercool my rig.

I plan to get:

1. Swiftech MCP655™ Series 12 VDC Water Pumps
2. Swiftech MCRES-MICRO™ Rev. 2 Reservoir
3. Bitspower BP-WBN79AP2-BK BLACK FREEZER MOS N79AP2 Water Block
4. Bitspower BP-WBN79AP1-BK BLACK FREEZER MOS N79AP1 Water Block
5. Bitspower BP-WBN79NS-BK BLACK FREEZER 790i NB/SB All-in-One Water Block
6. Swiftech Radiator - MCR320 Quiet Power Series Triple 120 mm - Black
7. Swiftech APOGEE GTZ Ultra Extreme Performance Universal Water-block
8. Swiftech HydrX Coolant
9. Bitspower Premium D5 Pump Mounting Bracket
10. Yate Loon 120mm High Speed Performance UV Blue Case Fan with Blue LED - D12SH-124UB - Sleeved
11. Koolance VID-NX295 (GeForce GTX 295) [no nozzles]
12. Koolance Coolant Temperature Sensor Plug, G 1/4
13. Siverstone RadSupport09 - Radiator Support for TJ09/TJ10 Chassis
14. Koolance Nozzle Pair, G1/4 Barb [13mm, 1/2"] - for radiator, resevoir, GPU
15. PrimoFlex Pro LRT Black Tubing -1/2in. ID X 3/4in. OD (about 10 ft)

I need ur suggestion and opinion on the above items.

Thanks

This post has been edited by rublik: May 4 2009, 03:06 PM