Welcome Guest ( Log In | Register )

Outline · [ Standard ] · Linear+

 Kitchen Sink, which one

views
     
lowyat101
post Jan 3 2023, 03:27 PM

Look at all my stars!!
*******
Senior Member
2,544 posts

Joined: Sep 2011
QUOTE(jlbb @ Aug 26 2022, 10:02 PM)
Hi all, im looking for sink for my new house, after reading some pages in this post, those brands like sorento, teka, levanzo are way out of my budget. Wondering if those shopee one few hundred bucks boleh pakai or not.

user posted image

Am i right to say top mounted sink is more suitable in wet kitchen as it is more frequently used? Dry kitchen can have undermount since use lesser and also look nice?
*
Hi, have you bought your sink? I'm also surveying for it and see this type a lot in Shopee. Cheap and claimed that it's 3mm or so. Not sure if it's true?

lowyat101
post Jan 3 2023, 03:32 PM

Look at all my stars!!
*******
Senior Member
2,544 posts

Joined: Sep 2011
Also I'm planning to use the old school concrete top with 2x2 tiles for my wet kitchen. Would it be possible to fix a undermount sink (like the picture below) to this type of concrete table top?

As I think it's not easy to cast the concrete to the precise dimension to fit the sink, also if they can cut the tiles so precise as well. So not sure if it's suitable to use this type of sink.

Thanks

Attached Image
lowyat101
post Jan 4 2023, 03:19 PM

Look at all my stars!!
*******
Senior Member
2,544 posts

Joined: Sep 2011
QUOTE(jojolicia @ Jan 4 2023, 11:42 AM)
Yes, its doable and its a common setting.

Just make sure to buy your sink, hood & hob and pass them to your contractor before start work

Consider granite top. instead of 2x2 tiles
*
Noted with thanks.

About the granite top, is it something like those used on the melamine kitchen cabinet? As I'm planning to use the RC top for the wet kitchen, not sure if this is suitable?

lowyat101
post Jan 4 2023, 03:28 PM

Look at all my stars!!
*******
Senior Member
2,544 posts

Joined: Sep 2011
BTW I noticed that there are basically 2 tyes of finishing on the stainless steel undermount sink. With the curved corner vs right angle corner as per the pictures below.

May I know what are the pros and cons, and which one do you prefer and the reason?

Thanks


Attached Image

Attached Image
lowyat101
post Jan 4 2023, 04:33 PM

Look at all my stars!!
*******
Senior Member
2,544 posts

Joined: Sep 2011
» Click to show Spoiler - click again to hide... «


I see. From your experience, do you know roughly how much will this cost and what are the benefits if compare with the 2x2 tiles?

Thanks


lowyat101
post Jan 4 2023, 05:44 PM

Look at all my stars!!
*******
Senior Member
2,544 posts

Joined: Sep 2011
QUOTE(jojolicia @ Jan 4 2023, 05:28 PM)
I too have limited experience, just sharing.

Cost, you gotta check.

Quartz and granite hovers ard 25-30mm thick, meanwhile even if you use homogeneous tiles its only 10mm thick. Secondly Q & Granite slab weight (being heavier) sets in better in the mortar bedding, compare to tiles. 2x2 tiles tends to wrap at corners, you will have tile pointing flatness problem between tiles. For a kitchen counter top that is crucial (for me)

Any chopping area in particular, tiles is a no no (in my opinion, specially you mentioned 2x2)

For a one time mind free rework, engage a reliable wet trade contractor to do the RC from plinth to top finish. Don't forget the backsplash skirt
*
thanks for the reply

about the backsplash, since there will be wall tiles at the back, is it still necessary to have the backsplash skirt?

lowyat101
post Jan 6 2023, 11:55 AM

Look at all my stars!!
*******
Senior Member
2,544 posts

Joined: Sep 2011
» Click to show Spoiler - click again to hide... «


thanks for the info, will look around about this as well.



lowyat101
post Jan 6 2023, 11:58 AM

Look at all my stars!!
*******
Senior Member
2,544 posts

Joined: Sep 2011
also about the pillar tap for sinks, normally for the dry kitchen i see it's bottom mounted.

for the wet kitchen, as i plan to use the normal 2x2 tiles for the table top, normally i see the contractor will put the water outlet on the wall instead. as i'm planning to use those extendable tap, mostly they are available in bottom mounted type.

would like to seek for some advice regarding this, bottom mounted tap vs wall mounted, pros and cons, etc.

thanks in advance


lowyat101
post Jan 6 2023, 01:42 PM

Look at all my stars!!
*******
Senior Member
2,544 posts

Joined: Sep 2011
QUOTE(mini orchard @ Jan 6 2023, 12:28 PM)
It can be done under the sink. Your contractor should know if that is your requirement.
*
ya i think so also. but just wanna see if there are any other pros and cons regarding the bottom mount vs wall mount.

from what i can see, for the wall mount tap, the table top will be clear and easier to clean. but might not be possible to have the pull out type as will need to hide the hose below the sink.

would like to see if there's any other considerations about this positioning of the tap?

lowyat101
post Feb 14 2023, 11:56 AM

Look at all my stars!!
*******
Senior Member
2,544 posts

Joined: Sep 2011
I noticed that nowadays, some sinks are without the small hole opening at the top part for water overflowing. Just to ask, if this is normal?

Thanks

 

Change to:
| Lo-Fi Version
0.0411sec    0.49    7 queries    GZIP Disabled
Time is now: 2nd December 2025 - 02:48 PM