I thought already got 1000Mbps aztech plug.. Why introduce 500Mbps.. Why not just extend 1000mbps series..

Any idea if home plug can work in 3 phase electric wiring?

All network components must be on same phase wiring.

Do you understand how the 3 phase wiring layout at your premise?

that... need to find out. thanks.

hi, i have one 110EW n 110EP,

1)can i know just plug both into power socket can use already?
or need to press the connect button below at the same time for pairing only can use?

2)my BTU at level 2, can i jus attach the cable from BTU to 110EP, then another side attach with 110EW with router?

BTU+110EP----110EW+router (then only come out with iptv LAN4 and PC with LAN1)

TQ.

you need one pair in order to work.

e.g. use 110EW and plug the cable from RG to 110EW. then another plug (110EP), use the cable to plug into your pc/notebook. then can use already.

cannot plug from BTU to 110EP...

Yup.. agreed. Please refer to manual how to pair it

Bought a pair of these recently (the latest Aztech 500MBPS with passthru), when my WIFI-N starts lagging when streaming HD movie...it works fine...speed is maybe around 170Mbps, according to the Aztech software....but now, the WIFI N300 is ok again...suspect it could be TVERSITY having problem previously due to cache/temp files too full...now no lagging after i clean up the cache even when streaming uncompressed BD over 30GB++ on the Wifi-N300.....regret blowing RM260 on the pairs of homeplugs...haiz....

Anyone wanna buy? Might wanna let it go.

I m using tplink home plug. My setup is BTU to Homeplug on 2nd floor and Homeplug to Router on ground floor.

Works fine

There is no chipset support 1gbps. Maybe you come accross with gigle that some manufacturer used for 1gbps. But the problem is i think gigle not in the homeplg alliance and it will make it difficult to interoperability later.

---

Added on August 28, 2011, 6:23 amActually homeplug ' connected' through the neutral cable in 3 phase wiring. So, u still can connected but maybe not strong connection.


This post has been edited by ntah_le: Aug 28 2011, 06:23 AM

How much does this Homeplug cost and does it comes in pair?

I bought a pair of tplinks home plug av at rm150, from sri computer. the slower non-av was less than rm100 for a pair (if I remember correctly)

Can I know if my mobo (MSI P67a-GD55) network chipset can support Aztech 280E which is 1000Mbps?

what is the diff between AV set and non-AV set?

(apart from bandwidth)

the problem is my setup: BTU- 110EP (2nd floor) to 110EP- RG (1st floor), works fine on both iptv n data.
but if: BTU- 110EP (2nd floor) to 110EW- RG (1st floor), cannot use at all, i only replace one 110EP with 110EW cannot work, all paired already..

should be ok for both... maybe u need to pair it again..

Guys, please be aware of the Aztech HL280E (1Gbps model). I read from somewhere that mentioned about the stability and heat issue with this model. That is the one of the reason why Aztech went back and come out with the new HL115EP which has lower speed than the HL280E.

Do google around to decide which one suit u better. And I don't you need the 1Gbps connection unless you are doing a lot of streaming from your local storage.

Yeah.. better buy 500Mbps homeplug. HL115EP is on of it. Because of the Homeplug alliance and interoperability.

I would like to setup two pairs of Homeplug with the following setup:

1st pair (for IPTV)
1. 3ph 415V
2. BTU@1st floor>RG>(LAN 4 from RG)HL115EP>wall socket
3. wall socket>HL110E>Set Top Box>HDTV

the problem now is how should I set up another pair of HL115EP for DATA from RG? Is there a configuration to set the Homeplug to recognize which Homeplug I want it to recognize? (i.e. 1st pair for IPTV, 2nd pair for data). Please guide me, tqtq

How about distance?
I had the unifi install at my office, but wanna use the IPTV at my home which is just opposite, around 100m.

Currently using maxis home at home, don't know when the IPTV will come