Need help. ... i can run prime95 for about 2hours and no BSOD/error dectect, but when i run ITB it cant even pass the standard test 1... got BSOD and i have tried up the v.core up to 1.525 but still get BSOD (even at 1.545 i get 0x101 BSOD error...ouch) but how can i run prime95

Here my rig.

CPU - i5 2500k @ 5.0 (c.volt:1.515, temp max 75@prime 95, others i set too auto, need to check for more details if someone can help here)

But if i run multiplier at *48 then can use ITB at max setting....
so is my current volt need to be added??

So here my current setup... before this it was OC @5.0ghz but get BSOD when tested with ITB but can run prime95 for 2hours with no problem, so i adjust abit and this is what i used for now:
CPU@ 4.8Ghz, temp max 74, c.volt read @1.465 (in bios) tested using ITB max setting and 1.488(gpuz)


I really want to get the 5.0 Ghz if can..... full load temp below 85 >.<

mobo - Asus ext IV-z
psu - silverstone AX 850
gpu - giga7970 oc @ 1025/1450
RAM -4G*2 G.skills ripjawX F3-12800CL9D (1.5v, dint OC yet becaused i dont know how)


PS: or i just need to run in standard mod for ITB? is the maximum is too much? because it used all the RAM?

PS:my CPU was water cooled, GPU not yet as dont know where can i get the block..

This post has been edited by kambing69: Jan 29 2012, 08:11 AM

I cant go more than 1.45 . . . seems like the max would be 1.45 for this mobo because it waill give warning..


edited: wrong i can go up to 1.545 >.< but get error with IBT

This post has been edited by kambing69: Jan 29 2012, 08:44 AM

That **** to know

O.o i got around 122.xx to 125.xx @ 4.8ghz~ (speed GFlop) (multiplier 48)


Maximum Turbo Ratio (multiplier i think) 48
BCLK 100
memory Freq AUTO
Internal PLL OV AUTO
Memory Bandwith booster DISABLE
-------
DRAM 9-9-9-24 @ 1.5v

------[CPU Performance Setting]
Enchance Intel Speedstep Tech ENABLE
Turbo Mode Enable
Turbo Mode Parameter - Max power - ENABLE
CPU core current limit 1023.875
CPU I/O limit AUTO

------ [DIGI+VRM]
VCore PWM mode EXTREME
VCore MOS volt ctrl AUTO
VCore load-line 75% (suit for 4.8~5.2)
VCore Switching Freq MANUAL
VRM Fix Frequency Mode 500khz
Vcore Phase Control Extreme
VCore over-current protection Disable
IGPU load-line Calibration Auto
IGPU Current Capability 100%
VCore EMI Reduction DISABLE
VRAM Over Temprature Protection DISABLE
--
VDRAM Switch Freq AUTO
VDRAM Phase Controll Enable
VDRAM Disable
--
VCCSA/IO Freq AUTO
VCCSA/IO Full Phase Control ENABLE
VCCSA/IO Over-current protection DISABLE

------------
Extreme OVENABLE
CPU manual[ Volt 1.490
IPGU offset mode +
DRAM volt 1.5000
DRAM other's (all AUTO)
VCCSA/IO Volt 1.125
CPU PLL 1.8750
PCH Volt AUTO
PCH PLL Volt AUTO
NF200 AUTO

Skew Driving VOLT AUTO
BCLK Skew AUTO
CPU I/O AUTO

CPU Spread Spectrum DISABLE

--------------------------------
Max temp (GT.Temp) 70, 78 80, 77 why the core temp so much diffrent between the core? how can i make sure the mobo give volt nice to all -to optimize the heat

SEEM's this is the best setting i can get, because run all the stress test and it past..... but if anyone know anything (tips) for OC up to 5.0 and above give me a hint please

around 122.xx~123.1xxx what this mean actually ? higher or lower better
@ 4.6ghz (multiplier 46)
@1.390 corevolt
DRAM v 1.500
max temp 70
BCLK 100
other all auto...

4.2Ghz (mltp 40)
other i forgot because this is auto tuning from ASUS Ai suite
if im not mistake BCLK at 104.3
other's forgot...
Max temp 56 >.<


All this was tested 20round of maximum IBT and around 12 hours prime95 bleech



How to get 5.0ghz >.< what need to change (i mean other's from core volt)....

PS: sorry for the long data
really need help here

EDITED: add some parameters

This post has been edited by kambing69: Jan 30 2012, 03:45 AM

Yeah im using watercooled atm but after 1.545 volt it seems it still cant hit 5.0... nah, my chip really bad maybe... oh well i think im ok with 4.8ghz@1.490

Let hope next IB will come in with 1155 sc and i get a good proc..

Ahaaaaa..... that an idea!!!

I will try to off all the AutoBoost and off all the ECO saving features . . . and will try if i can hi 5.0 or not... Maybe the volt inside the motherboard not stable because of the auto boost ?

wish me luck~

EH wait..... convert to RM + shipping how much?