There is no NB in P67. That old NB area u saw on board is actually replaced by NF200 chip. SB has been replaced by PCH. With PCH at default 1.05v, it wont be hot and doesnt affect OC at all.
In fact the whole board of X58 is damn hot and power sucker.

owikh, have you got your m4e replaced with b3 rev?

Not yet bro i was told by CEX that Maximus B3 will be ready to swap on 15/3. Meanwhile UD7 B3 will be ready by next week, as imformed by NationTech PG. But need to double confirm with him again later... later bro.

Maximus IV Extreme -UEFI 1298 BIOS

http://91.121.148.119/downloads/BIOS/Maxim...e-ASUS-1298.ROM


Thanks cstkl 1.

This post has been edited by stasio: Mar 11 2011, 10:14 AM

models from gaygaybyte oso can swap ar ?
ud3 got b3 revision swappable soon ?

All manufacturer edi start swapping program. Just the matter of whos fast, whos slower

Currently leading the race is MSI > ASUS > GIGABYTE for the main top mobo "taiko"

Guys,anybody got new Gigabyte P67A-B3 series mobo?

This post has been edited by stasio: Mar 12 2011, 07:22 AM

can i change it like in april?

Intel Core i7 2600K @ 5.040 GHz HT ON (4C/8T) = 105 x 48
Asus Maximus IV Extreme 1298
2x2GB G.Skill RipjawsX 2200C7 @ 2240Mhz 7-10-7-27-1T
2x MSI GTX580 SLI, 930/4100Mhz
Corsair AX1200

hmm is that the lowest vcore u can go with 5ghz? kinda high.

he is running 100 percent loadline, brave fella aint he .. whacking voltages. vccio is correct. 1.075v up to 2260mhz np.
i tested on of my m4e set 100% loadline at 1.40 . dmm read 1.44v, cpu read 1.42v on load
so far up to 1.5v i tested recommend only to use 75 percent loadline on m4e and rest of asus ultra high on loadline ( this is the 2nd highest loadline)
for most accurate reading.
Tins in depth review also confirms this but at higher but he measures from the cpu socket's so should be more accurate

http://forums.xtremelabs.org/viewtopic.php?f=90&p=24023

i can do ht on but dunno stable or not cause cannot run ht off since temps are way above my comfort level

nice clocks owikh.. tuning time to increase that bandwidth.

This post has been edited by cstkl1: Mar 12 2011, 09:47 PM

Intel Core i7 2600K @ 5.355 GHz (2C/2T) = 105 x 51
Asus Maximus IV Extreme 1298
2x2GB G.Skill RipjawsX 2200C7 @ 2240Mhz 7-10-7-27-1T
2x MSI GTX580 SLI, 930/4100Mhz
Corsair AX1200

eh so ure proc max is more than 5.3..

how far is ures ??

mine is max 52.

yaya 5.355GHz is the freq wall for this CPU from batch L048A937. Not so good but not too bad.
max BCLK 106, multi x53. Unless future BIOS shows magical improvement. 106x53
somehow it's not the best I have as the 1st one which could do up to 5.447GHz (sold)
I've stopped hunting for the so called golden 2600K bro unless someone wanna let go his baby.

well i have a 41C108 and it sux bad. paid a lot for this and here ends my batch hunting also.

lol

I feel u. They found good CPUs bcoz like this bro

hmm but ure voltage for that 5050 vcore me dont think its that stable but aint that far also

so far in sandbridge i noticed this
say example 4750 my 24/7 clocks

vcore is between 1.400 set to 1.420
glops will pass between 79 - 82glops

lower end glops neeeds 1.4
higher end glops needs 1.42

but heck if u have a 5ghz proc that does 1.36-1.4
dont think that 0.02 hurts lol

My G.Skill F3-17000CL8D-4GBXMD arrived, March 2011 with nice black PCB.





Default setting:



This post has been edited by stasio: Mar 14 2011, 02:20 PM

Nice stasio! Show some oc potential of the ram

yup i am waiting also

still skeptical on this ram on runmc and dumo testing just that one kit
and honda and chew doing a overvolted run.

btw if u find that ram boring and not what ure looking for got a ready buyer here lol
hint hint acther ,stasio

This post has been edited by cstkl1: Mar 14 2011, 02:56 PM