So lets say if i have installed win7 on normal hdd. But i install a game like crysis on the iSSD, will it run faster?

---

Added on July 29, 2011, 10:29 amAs in performance i mean.

This post has been edited by AlphaBeta: Jul 29 2011, 10:29 AM

It should load faster

are u sure??
huh,i tot 16GB space is for 32 bit...

ur games will load faster for sure...

I believe u didnt stress enough RAM amount.
Pls include Task Manager performance tab to show mem/CPU usage during load.

Prime95 custom blend full RAM min FFT 128 for 6 hours.

LinX full RAM on W7 x64 SP1 20/50 runs.

Btw BSOD during idle can be overcame by enabling all the power saving feature EIST, C1E, C6/3, etc

---

Added on July 29, 2011, 11:50 amA freshly installed W7 x64 SP1 + Dirt3 already used up 40GB of my raided SSD.

This post has been edited by owikh84: Jul 29 2011, 11:50 AM

First time see this BCLK frequency 4.2.

How much i can increace?

that is a bug on Asus mobo bro.
Do u flash the latest BIOS?

i just received the mobo today and i shock to see 4.2 only. zzzzzzzzz

I got the same issue with my old MIVE B2 last time.
I couldn't change the BCLK some ppl told me that IME part of the BIOS chip is corrupted.
Pls update Intel Management Engine (IME): http://downloadmirror.intel.com/20261/eng/....14.1107_PV.exe

The problem fixed finally.

Still got one error. the mobo display code 53 error definetly. This can be avoid if i dun plug any ram in slot number 3. Any solution for this?

I use asus gene z.

clear ur CMOS and see. I believe u need to change ur DRAM settings abit.
53 shows DRAM OC failure (wrong settings).
Using slot A2 and B2 (slot 1 and 3) for 2 sticks is correct.

just check all the slot one by one, slot 3 is dead.

1, 2 and 4 is working perfectly. Now using 2 and 4. zzzzzz

Sounds bad bro. new mobo wor...
nvm slot 2,4 can be used just fine.

My previous EVGA mobo, I thought one of the RAM slots is dead.
manatau observed it closely, found dirt stuck on the slot contact pins I guess it was TIM residue dropped inside the slot. Put in & out the RAM for quite some time, then only the RAM was finally detected & running flawlessly.

packed the gene and ready for rma since i eligible for 1 to 1 exchange. Luck in not on my side this time. lolx

so fast!? ok go 1-to-1 swap b4 it's too late. Good luck!

what is LINX? and how to test it? btw, which one is more good, Linx or Prime95?

i prefer LinX (as per link on 1st page) with Win7 updated to SP1
if u happen to test it, please post the result here..

a program to stress ur comp?lol..
linx stresses more wit win7 SP1..
make sure u choose the right version (32 or 64) then click all and select how many times u wan it to run.. at least 20 runs

which problem size and memory(mib) i should choose for the testing?

guys OCing an i7 2600k on a MSI Z68MA-ED55 mainboard, cooling it with a H50 dual fan push-pull setup

pushing it at 4.2MHz and the CPU temperature went up to 74-81c at full load. is that normal? stressing it wit prime95 for about 5min and couldn't bare to continue looking at the temperature, had to stop it right away.

some advice on cooling or maybe a better oc settings? mainly use for rendering



thanks guys

reduce ur vcore notch by notch until u get BSOD.
lowering CPU PLL from 1.8v default to 1.6-1.7v (depends on CPU) also will help in reducing the temps.

stressing 2600K HT on H5O is like that, unless if u wanna turn off HT & run cooler.
there's a way to improve the performance of H5O, put the radiator at area near 5.25" HDD bay give it better intake air.
get a better CPU cooler ie. H100 or Noctua DH14 etc.