Thanks for those replied me.
Yeah im using the AM3 BTK, well i dont want to remove my mobo just to change the heatsink direction >_>

Vx is thicker than TRUE so i think angrysnail might be correct.

but nevermind gonna sell off my 890fx liao lol.

wah..upgrade to what bro?

@cloudwan @kuntawakaw @usop8290

the board I am using is Asus M4A88T-M/USB3 , I just notice I can't under voltage via BIOS. This is strange.

I think the bottleneck is my RAM (Mushkin 4GB essential), I am sharing it with the built-in GPU.

Spec: X3 440, Asus M4A88T-M/USB3, Mushkin Essential 4GB, Seasonic SII 520W. No GPU.

This post has been edited by mitodna: Jan 1 2011, 11:34 PM

990FX with 8core Bulldozer lah
lol jk only.
Downgrading to 870 chipset, im unable to utilize my mobo much for now due to lazyness plus too miskin to buy dual GPU lol.

1. Have u tried turning off load line calibration & cpu-nb load line calibration?
2. Ur using manual mode or offset mode to reduce the volt?

@cloudwan , latest status, it seems that anything after 13*250 = 3250MHz will BSOD, still can POST, but can not even tahan 10 minutes on Prime95

Now I am on 13*250, while posting this.

On your hint:
1. Hmm, I saw that option, I leave it default
2. How can I see the mode? For the voltage, I can only press +, press - will lead to auto. Hmmm

you sure your rams can run @ 1000mhz 6-6-6?

don't know, was quite stable, but I have change to the SPD one, 1000MHz 7-7-7-20-27

This post has been edited by mitodna: Jan 2 2011, 12:41 AM

Unless your CPU is lemon chip lol, most new chip 1.4v can run 3.6ghz or above already. while Thuban 1.4v can run 4GHz already, but its pretty hot at that voltage unless you have some best aftermarket cooler installed.

btw, what is your voltage? how bout your temp?
im planing to oc my 1055t to 4GHz

1.35v, but unstable, i guess my chip need 1.425 something. Well currently im stuck at 3.7GHz, i guess my RAM is the culprit here because i used up all the ram slots.

Temp never reach 60c of course, in aircon room
Using Vx with 2 f--king loud SFLEX-G clone (Sony SFF21c)

Expect RM3K++ procs from AMD as well?

hard to get chip emas..unless you are lucky guy
without aircond my chip never reach 60c oso idle at 28c using true120 with 1 fan..
need to buy another fan clip to mount 2nd fan before oc at 4GHz

helo, my phenom fx-5000 shud be can oc above 3ghz rite? but everytime i try get pass 3ghz then my com cant boot le, i tried bumping up my NB voltage by 0.1v and my vcore to 1.36v and lower my ram to 667 speed, but comp still cant boot, can help?

This post has been edited by darkbat123: Jan 2 2011, 10:57 AM

28c? U got that reading from the core temp or cpu temp? If core temp take it with a grain of salt lah..
Use the cpu temp, core temp is a bit misleading

---

Added on January 2, 2011, 11:02 amWhy u wanna bump ur NB volt? Bump ur CPU-NB volt instead not ur NB..
BTW list ur spec & what setting u use for us to easier help u troubleshoot ur problem

This post has been edited by cloudwan: Jan 2 2011, 11:02 AM

Maybe yes maybe not.AMD got said,eventhough they release FX variants there will still a mainstream parts.So no worries actually.

But from the point branding "FX",it means AMD is already speculating/expecting that their new Bulldozer should perform as good as Intel.

What i like is the "FX" suffix.I wish to have it to,its just nice.Just like some of us here like the processor detected as AMD Opteron

GA-MA74GM-S2
kingston pc2-5300 @ 5-4-4-12

cpu-nb??? is it "northbridge voltage" or "NB VID"?
= = im not very good at these things, sry

This post has been edited by darkbat123: Jan 2 2011, 03:41 PM

Give us your CPUZ CPU and Memory Tab Screen Shot.

For now,set your ram timing to 5-5-5-12 first.

cpu tab


mem tab




This post has been edited by darkbat123: Jan 2 2011, 11:49 AM

Now stable or not?

If not pump CPU Volt a little.