I'll send them for RM3 poslaju
No tips.
No charging.

having problem with my usb adsl modem (prolink 9000p)

anyone using this (via the usb port) and know where to get the usb driver?

Ya,i also have this problem for my Aztech DSL306U,i sent Aztech an e-mail to get the driver and they sent me the files with rpm but it didn't work.

Last time I checked..
It's just difficult to get USB Modem to work with Linux..
Better off getting an Ethernet based modem.

as far as my knowledge knows, it's almost impossible for most linux distro to support a usb based adsl modem. whereas an ethernet based is mostly well supported.

I'm having this problem when booting the installation disk...
it stops running after the line:

[#:#] ata1: sata ...blablabla... irq18
[#:#] ata2: sata ...blablabla... irq18
[#:#] ata1: dev 0 ATA, max UDMA/133, 156301488 sectors:

note: #'s are some numbers

then my cdrom stops running, no hdd activity either...

i have 2 sata hdd which i think shud b detected correctly as in the first 2 lines. the last line shud b my cdrom. correct me if i'm wrong... noob here...

can anyone help pls?

my modem support ethernet, just that my pc dont have the ethernet port/network card. xD

my limited knowledge tells me that the last line should be a hdd.
try removing one hdd, and install again, see if the problem still persists.

alamak, nic very cheap lar now.

I suppose you are using an ancient mobo without on board lan?

It's a sign you should upgrade your pc dude..

Are you using breezy?

Warty is current having some problem with writing boot record into SATA drive with another PATA drive present.. The solution is to yank the PATA drive out..

I heard hoary users have to do the same thing too...

nope. my mobo come with the ethernet port. but it strike by lighthing and its no longer functioning.

i think jwlam using is both sata drive. but both shows irq18, could it be irq conflicts?

I dont think so.
In Linux, if there is irq conflict, it will tell us that something is too busy on that channel...

He needs to tell us which ubuntu he's using after all.

Ubuntu and SATA is a particularly widely discussed subject ever since Ubuntu was released a few years ago.

sry for the confusion. i'm using Ubuntu 5.10 (Breezy Badger) CDs i requested from https://shipit.ubuntu.com/

i'm using 2 sata hdd n i've tried disabling 1 of em in the bios (din unplug thou) and problem persists. i even disabled all my extra rom drives (dvd, cdrw)...

thx.

today i booted my Ubuntu from a P4 2.8ghz based machine.

at first i tried my HDD installed Ubuntu. it stops at mounting drive. ok so fine, i tried other IDE slots, changing master to slave just in case the device settings and such - didn't work either.

ok so i then tried other ways of booting, like recovery mode - didn't work either.

so next up, LiveCD. strangely it'll reach the language preference part and refuses to move........AT ALL.

at this point - it gets pretty annoying. tried other keyboard (not via KVM) - didn't work either. tried it just to confirm, cos it's really weird. how could one access BIOS and manage settings yet not able to choose language?

it's really strange as i've actually used Ubuntu on this particular machine before and it worked flawlessly.

so fine, i recalled my earlier use was on a P4 2.4 and not a 2.8. so i switched the P4 2.8 to P4 2.4 (both are 512kb /533fsb models) and voila!!! it worked!!!!!!

strange? yes it is..... do they have a ghz limit or something? i doubt chipset was an issue either.

i just installed ubuntu 5.10, downloaded iso and burn into cd.

i have no problem installing it, but now i have a few problem configuring it. Please provides step by step guide will be the best,

1) I have successfully configure the linksys wpc54g to run using WEP.
my problem is, how do i configure it to use WPA? I need to configure in WPA. And how do i load the driver when startup, what i do now is everytime startup, i type "sudo modprobe ndiswrapper".

2) i want to play, mp3, divx and etc in totem, i have configure according to this website https://wiki.ubuntu.com/RestrictedFormats, but it display error of "dependencies error"

thank you.

anyone on hoary 5.04 manage to execute ndiswraper(sp?)?
i manage to compile the driver for my dlink g122, and the device manager detects it correctly
but in networking, my usb isn listed?
do i need to upgrade to 5.10 juz to get dlink working with ndiswraper?

p/s: tried all possible dlink tuts/tips on forums, but fail to execute ndiswraper
p/s 2 : yes, my g122 is supported, coz its rev2

haih~

hi everyone...i installed ubuntu 5.10 server mode..how to login this..i tried everything..how to log into operating system...er new to this want to try it any guide for server mode

thanks guys

didn't they ask you for a username and password during installation?

yup they ask...i fill..then after finish installation..i login n give passwd..nothing happen it like this usr@usr :"$