Welcome Guest ( Log In | Register )

Bump Topic Topic Closed RSS Feed

Outline · [ Standard ] · Linear+

 Samsung Galaxy S I9000 Official Thread V4, Please read FAQ at 1st page!!

views
     
frankgan
post Sep 24 2010, 12:49 AM

Getting Started
**
Junior Member
259 posts

Joined: Nov 2007


Hey guys,

Help!!

My SGS ran out of battery just now, when I reconnect it back to charger and turn it on, it wont and it stays at the shining S.

How?

If you're asking whats abnormal before the phone ran our of battery is that I set it to vibration mode.

Thats all I can think of. I din do anything unusual sad.gif
frankgan
post Sep 24 2010, 07:40 PM

Getting Started
**
Junior Member
259 posts

Joined: Nov 2007


QUOTE(pcboy @ Sep 24 2010, 01:01 AM)
Have you tried to pull out the battery and switch it ON again?
*
QUOTE(silentser @ Sep 24 2010, 01:31 AM)
a quick question, do you apply one click lag fix?

if you do that maybe the case here, it happen to me once, my phone hang, and i just pull the battery, when i on again, it stuck and vibrate

then one of the forumer here say, it cause of the one click lag fix, it have corrup your system file or something like that, the only way is to reflash i guess,
*
QUOTE(janov @ Sep 24 2010, 09:01 AM)
Did you managed to charget he battery? Try not to over-drain the battery, once the battery voltage level reaches a certain low level, it will go into sleep mode and a trigger in the circuit of the battery needs to be done. you might still be able to claim warranty if you still have the problem, just remember never to over-drain the battery it causes a lot of stress on it which reduces its life cycle, next time if your battery is low charge it right away but if you do not have access to a charger turn the phone off.
I did pull out the battery and try but still no luck sad.gif was forced to hard reset the phone through vol up + home + power sad.gif everything gone now.

I think its just as the silentser has mentioned, the system crashed due to one click lag fix. Even after hard reset the phone performs abnormally, constant hangs and no response etc. A new flash to another firmware has solved my problem.

I assume I managed to charge the battery because I was able to turn it on. It just wont boot into the system but stays at the glowing S. sad.gif
frankgan
post Sep 30 2010, 01:24 AM

Getting Started
**
Junior Member
259 posts

Joined: Nov 2007


QUOTE(mengsuan @ Sep 30 2010, 01:06 AM)
The new KIES broke the perfectness in my system. Now, if I press firmware upgrade button, it says no new firmware like usual. When I close it, that firmware update windows hangs and require force closing.

I think I'd return back to old version or uninstall it entirely. KIES is pretty useless in my needs.
*
I use kies just to sync contacts with microsoft outlook.

any alternative to sync contacts or how to backup using titanium backup?

anyone care to teach?

I hate kies in fact, so slow and useless
frankgan
post Sep 30 2010, 07:47 PM

Getting Started
**
Junior Member
259 posts

Joined: Nov 2007


Hey guys, I have just flashed to JM8, but the battery life was =.=.

Does that have anything to do with the modem / CSC files that I used during flash? Can I change it to the CSC/MODEM file that I used in JM2?

I was on JM2 and the battery life was much better. Why? Btw, how to use titanium backup? can anyone teach me?
frankgan
post Oct 2 2010, 03:10 AM

Getting Started
**
Junior Member
259 posts

Joined: Nov 2007


Hey guys,

do any of you experience the problem of cannot sync contacts with facebook/outlook/ etc after you apply the one click lag fix? is it me or everyone is experiencing the same problem?

Btw, can I mix JM8's PDA file with JM1 Modem and JM1 CSC when I flash?

My battery was draining like water after I flashed to JM8, does that have anything to do with modem / csc file I used? or the lagfix?

Topic ClosedOptions
 

Change to:
| Lo-Fi Version
0.0399sec    0.96    7 queries    GZIP Disabled
Time is now: 11th December 2025 - 01:37 AM