Outline ·
[ Standard ] ·
Linear+
~**Proton CPS Tribe® V8**~, »»»Power That Means Business«««
|
singchaii
|
 Nov 18 2010, 10:17 PM
|
|
QUOTE(R.Y.D.E.C.K @ Nov 18 2010, 02:36 PM) 1 question> for those who`s change timing belt or for singchaii to answer  ...issit necessary we change the water pump too during timing belt changing process?if yes wut brand shld we buy? n issit possible if i wanted to change whole belting??will change the timing belt end of this month.. If we follow the service manual, when change timing belt then is time to change water pump, accessory belt and accessory belt tensioner. But we can skip if the part is still usable. But for new batch of campro, water pump confirm leaking when we remove the timing belt because of poor quality. Water pump we buy AISIN brand. But make sure is original AISIN which the brand is punch on the waterpump. |
|
|
|
|
|
singchaii
|
Nov 21 2010, 05:35 PM
|
|
|
QUOTE(mrl @ Nov 20 2010, 11:45 AM) belt clip can break from accident??? how strong is the impact??? what car is that?? It can be due to improper installation or manufacturer defect. As I know for that citroen, once it accident then the safety belt got the pre-tensioner which lock the safety belt so the passenger won't throw out from the car. Same as in waja cps. |
|
|
|
|
|
singchaii
|
Nov 21 2010, 10:55 PM
|
|
|
QUOTE(TripleJ104 @ Nov 21 2010, 10:19 PM) Yup...drive safely. Anything can happen. The car is not my cousin car, its workshop car. My cousin use it coz his car was in workshop.. Cause the accident was power steering malfunction & all around dead suspension. Anyway i wanna ask our cps need how many liter of engine oil? What i remember my mechanic pour all 4 liter engine oil.  Basically it need 4 liter for the indicate to maximum. But for more performance and avoid engine oil leaking from oil seal, it good to pour the engine oil level between minimum and maximum. |
|
|
|
|
|
singchaii
|
Nov 23 2010, 06:07 PM
|
|
|
QUOTE(TripleJ104 @ Nov 22 2010, 09:19 PM) Huhuhu...just happen u just posted few second when i open lowyat. Oooo..profile 50 arrr. I not quite sure kl price, but under rm300 should can get yoko r1, gsd3, hankook v8, falken 912, & bridgestone. What i heard yoko s drive is very good..but IMO, better invest a good tyre.
Added on November 22, 2010, 9:20 pmThat very cheap worr..here at jb at least can get rm280. Yoko T-1r can get below RM300? I'm using Yokohama S-drive. I bought RM420 per pieces. QUOTE(Azuma-kun @ Nov 22 2010, 10:09 PM) Chamber nut eh. Which spare part shop? Any shop? How old is your car? Why it need chamber nut? Only accident car need chamber nut. |
|
|
|
|
|
singchaii
|
Nov 24 2010, 07:29 PM
|
|
|
Finally I got my project car dream come true. Hehe. I get a kelisa to play turbo. Seldom drive my waja unless outstation now.
|
|
|
|
|
|
singchaii
|
Nov 29 2010, 06:20 PM
|
|
|
QUOTE(sphiroth @ Nov 29 2010, 10:18 AM) AFR too rich at really high rpm.  AFR rich won't cause the engine light turn on. It will have fault code, but the engine light won't turn on. QUOTE(sphiroth @ Nov 29 2010, 02:29 PM) In my case, need to disconnect the battery for 2 minute. To reset the ecu, actually no need to disconnect the battery so troublesome. Open up the fuse box, you can see a fuse call 'memory'. Just pull up and then put it back.  |
|
|
|
|
|
singchaii
|
Nov 30 2010, 07:56 PM
|
|
|
QUOTE(kcng @ Nov 30 2010, 05:57 PM) kereta rally, sure tapau semua la...  *cab0t* Wooiii.... How is your car? Hehehe |
|
|
|
|
|
singchaii
|
Dec 6 2010, 07:01 PM
|
|
|
QUOTE(mrl @ Dec 5 2010, 11:51 PM) i felt it's good enough already, though can be improved... maybe because i compare to my Wira previously... but still, it's weird coz i never had smoking hot problems before even running fast and 100% brakes, no engine braking (coz that time still noob... ) now afraid to use too much brakes already... got to check up the brakes first... I got pretty much oversteer when braking on corner (really hate those right lane hogger) Is time to have better tire and ultra racing bar.  QUOTE(senbe84 @ Dec 6 2010, 10:31 AM) Guys wanna ask something, do cps model have the same problem like previous campro....crankshaft snap into 2.still got ar those problem?Scared la wanna drive my cps like mad when remember this issue. No more such thing even is campro now. last time because of the manufacturer which cause that problem. Now it from different manufacturer. |
|
|
|
|
|
singchaii
|
Dec 6 2010, 07:59 PM
|
|
|
QUOTE(ahpaul82 @ Dec 6 2010, 07:23 PM) any guideline how to remove the throttle body? how to let the butterfly valve always 'open' to clean?  the butterfly valve will not move freely and can be easily damaged if forced to move against the resistance of the stepper motor. For throttle body which control by accelerator cable, you can open the valve to clean. But for campro, it risky to open the butterfly valve open because it fully control by the stepper motor. If you wanna clean it, try use those carbon chemical to clean it. |
|
|
|
|
|
singchaii
|
Dec 9 2010, 09:44 PM
|
|
|
QUOTE(ahpaul82 @ Dec 8 2010, 07:52 PM) i see, i just wonder is it very difficult to remove the throttle body? if can take out and clean would be much easy. Can said hard, can said easy. But better don't try. haha.. How many people here service they car at Pandan Jaya Proton Edar service centre? |
|
|
|
|
|
singchaii
|
Dec 12 2010, 07:41 PM
|
|
|
QUOTE(sphiroth @ Dec 12 2010, 10:17 AM) This part at the joint. Need to apply grease/silicon. SC can fix FOC. [attachmentid=1933791] Yes.. This what we usually did on waja when got chasis sound during uneven road or cornering. Apply grease/sillicon is not for long use. Usually we use punch and hammer to knock it. QUOTE(ahpaul82 @ Dec 12 2010, 06:49 PM) to Gen2 CPS users, anyone change trunk latch before? [attachmentid=1934582] After i removed and 'lock' it to the strike plate, it seems very loose, it is normal?  mine create a lot of rattling noise on this parts... Impossible the seem very loose. Got install correctly? You check the metal rod which connect lock to this trunk latch. usually is the metal rod knocking the rear bonnet metal. Try check and see. If it was loose, mean you install not correctly. |
|
|
|
|
|
singchaii
|
Dec 13 2010, 06:16 PM
|
|
|
QUOTE(R.Y.D.E.C.K @ Dec 13 2010, 10:23 AM) hey guys........ saya!!! dayummm...soo near mah! Last week you sent your car there service? Hehe.. |
|
|
|
|
|
singchaii
|
Dec 14 2010, 06:02 PM
|
|
|
Where got cheap bodykit? I thinking to install bodykit on my ride.. Any recommend?
|
|
|
|
|
|
singchaii
|
Dec 15 2010, 09:12 PM
|
|
|
Very bored with my waja cps. Having new vibrate sound from dashboard. Suspect is from left air cond vent. I so hate those vibrate noise.
|
|
|
|
|
|
singchaii
|
Dec 16 2010, 11:06 AM
|
|
|
QUOTE(R.Y.D.E.C.K @ Dec 15 2010, 01:05 PM) huh count me in for bulk buy..especially lips! huh Led old 1 better coz more brighter than tube 1... We go shop and buy. haha. Belakang tesco ampang. I think that shop cheap cause many club go there and TT to get bodykit. |
|
|
|
|
|
singchaii
|
Dec 17 2010, 08:32 AM
|
|
|
QUOTE(R.Y.D.E.C.K @ Dec 16 2010, 11:55 AM) heard bout tht too....soo when? im on..from now!  But i need go survey price. If cheap, then I tell you. Haha. Only can go install together. |
|
|
|
|
|
singchaii
|
Dec 17 2010, 12:16 PM
|
|
|
QUOTE(R.Y.D.E.C.K @ Dec 17 2010, 08:55 AM) ohh thnx...soo true im planned to go there survey tmoro..ehh tmoro need to pay visit to pandan jaya SC..gov ppl oledy got gaji...must be hectic then  been bz since 4 weeks back soo now onli got time Can you survey for me as well if you going there? I wanna know the price for waja cps lips, and r3 side skirt and r3 rear skirt. |
|
|
|
|
|
singchaii
|
Dec 18 2010, 06:36 PM
|
|
|
QUOTE(R.Y.D.E.C.K @ Dec 18 2010, 12:43 PM) still can use but myb not giving us fullest satisfaction... phewww....just change timing belt...RM390 Husin Rahman Service ( generation to generation family workshop) SPEC: mitsubishi t.belt 1 set kit - same code product number wif the original CPS waja original RM330 (100k km) made in japan Bando pan belt made in malaysia (japan factory produce) same code number with ori waja use too total pay RM390 finish in 3 hour.. my water pump still in best condition..they said my old belting can go another 10k km but the pan belt is ready to change to new one...got minor tiny crack (normal they said) they dont hv the oil tht i want to use as normal visit my family will bring the oil and oil filter...if not ady change everything.. current mileage is 91853k km.. later probably monday change engine oil + aligment + today SC Pandan jaya full to the max.. soo long didnt redlining ..finally Too many warranty claimed. I see they warranty claim alot saga blm, persona and exora. |
|
|
|
|
|
singchaii
|
Dec 18 2010, 09:46 PM
|
|
|
QUOTE(R.Y.D.E.C.K @ Dec 18 2010, 06:51 PM) actually since 3 month ago im trying to identified / surveying which t.belting our waja cps use..sooo the workshop suggesting tht y not we open all the casing and then check the belting...then try to identified which belting proton use then closed back...and im quite surprise too tht they use Mitsu...soo we call and ask the runner to buy base on the product code written on the belting wall...b4 ive been asking the SC and they giving me diff. code number and brand...some say this and tht..i stand beside my car from the start till finish..take few pic for documented porpose and to understand the replacing process..not like to learn n diy but just to know the steps tools and technics
Added on December 18, 2010, 6:55 pm ....dino is like here there... Haha.. Like this only dino can diet. QUOTE(pedanglaut @ Dec 18 2010, 08:36 PM) my mod today  [attachmentid=1946513][attachmentid=1946514] How much it cost? |
|
|
|
|
|
singchaii
|
Dec 21 2010, 07:00 PM
|
|
|
QUOTE(TripleJ104 @ Dec 21 2010, 12:43 AM) guys...now my car reaching 25k km..should i change petrol filter now or wait 30k km? Waja petrol filter can stand for 60k km. |
|
|
|
|
Quote
0.0485sec
0.27
7 queries
GZIP Disabled