Outline ·
[ Standard ] ·
Linear+
Intel® Core™2 Duo/Quad Overhauled Rev. 4, The journey continues...
|
alvinfks78
|
 Nov 1 2010, 11:01 AM
|
|
Hi, tried to Overclock the E2180 but am stuck at 2.20. It works fine at this speed.
however, immediately after increase to 223 or 226 and exit BIOS, it will go silent for a while then automatically resets back to default 2.00 before POST. Hope any sifus can give some opinion:help:
My Specs and config in BIOS are below.
Intel E2180@2.20ghz
Gigabyte mobo: GA945-GCM-S2L Revision 1.00 F4
2Gb 667 -PC 5200 Kingston value ram 4-4-4-12
sapphire 4670 512 mb
1 TV card
Windows XP sp2
1 DVD drive LG
1 USB wireless TP-Link
1 AVF 450W PSU (Cap ayam)
1 PCI fan
memory frequency multifplier = 2.00
FSB = 220
CPU Multiplier = (cannot change in bios)
PCI Clock speed = 100
vDimm = auto
FSB overvoltage = auto
Vcore = 1.325
EIST = Disable
CE1 = Disable
Temp = 48 - 65 c
Thanks for all advice. smile.gif
This post has been edited by alvinfks78: Nov 1 2010, 05:02 PM
|
|
|
|
|
|
alvinfks78
|
Nov 3 2010, 12:08 PM
|
|
|
QUOTE(saturn85 @ Nov 1 2010, 09:47 PM) try lower down the dram multiplier. since you are using DDR2 667 ram, default dram muliplier should be 1.67. try lower it donw to 1.33.  Thanks for reply   Tried to lower the multiplier for DRAM but lowest can go is 2.00. Memory Frequency 400mhz. But its still below 667mh right? If set to auto.......would not even start. shoot up to 7++ mhz. Maybe I can increase the timings? probably my Mobo limitations? ..........Googled..........other people's best bet was 1:2. I remember being successfully going to 2.23 or 2.26 once but can't replicate it again. This post has been edited by alvinfks78: Nov 3 2010, 04:16 PM |
|
|
|
|
|
alvinfks78
|
Dec 22 2010, 09:13 AM
|
|
|
Hey for OC. Does the age of the CPU affect Overclocking capabilty.
Tried to OC my 3 yr old E2180 but can't go above 2.2
This post has been edited by alvinfks78: Dec 22 2010, 10:58 AM
|
|
|
|
|
|
alvinfks78
|
Dec 22 2010, 05:10 PM
|
|
|
QUOTE(teoh123 @ Dec 22 2010, 05:03 PM) I'm not a good overclocker but I need some help to OC my q6600 above 3.2ghz I'm using GA-EP45-UD3R , 2GB 667 DDR2 1 stick RAM , others shouldn't be a problem Need help with my BIOS settings Here's the image http://img440.imageshack.us/f/asdbu.png/
Added on December 22, 2010, 4:05 pmMy settings,I need some help to tweak them » Click to show Spoiler - click again to hide... « GIGABYTE GA-EP45-UD3R
[u]MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:Auto
CPU Clock Ratio ..........................:9
Fine CPU Clock Ratio.....................:Dont have this
CPU Frequency ...........................: 3.0GHz(333x9)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............:333Mhz
PCI Express Frequency (Mhz) .........:Auto
C.I.A. 2......................................: Disabled
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mv
PCI Express Clock Drive.................: 900mv
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: Don't have this
(G)MCH Frequency Latch...............:[Auto]
System Memory Multiplier ..............:[Auto]
Memory Frequency (Mhz) ..............: 667................833Mhz
DRAM Timing Selectable ................: [Auto]
Standard Timing Control
CAS Latency Time..............................: 5..............Auto
tRCD .........................................: 5................Auto
tRP...........................................: 5...............Auto
tRAS..........................................: 15.............Auto
Advanced Timing Control [Press Enter]
tRRD...........................................: 3....Auto
tWTR..........................................: 3.....Auto
tWR............................................: 5........Auto
tRFC...........................................: 43.......Auto
tRTP...........................................: 3.....Auto
Command Rate (CMD) ....................: 0......Auto
Channel A
Channel A Timings Settings [Press Enter]
Static tRead Value.........................:6 Auto
tRD Phase0 Adjustmen.......................:0 Auto
tRD Phase1 Adjustment......................:0 Auto
tRD Phase2 Adjustment .....................:0 Auto
tRD Phase3 Adjustment......................:0 Auto
Trd2rd(Different Rank).....................:6 Auto
Twr2wr(Different Rank).....................:6 Auto
Twr2rd(Different Rank).....................:5 Auto
Trd2wr(Same/Diff Rank).....................:8 Auto
Dimm1 Clock Skew Control...................:Auto
Dimm2 Clock Skew Control...................:Auto
DDR Write Training ...........................:Auto
Channel A Driving Settings [Press Enter]
Driving Strength Profile...................:[AUTO]
Data Driving Pull-Up Level.................:Auto
Cmd Driving Pull-Up Level..................:Auto
Ctrl Driving Pull-Up Level.................:Auto
Clk Driving Pull-Up Level..................:Auto
Data Driving Pull-Down Level...............:Auto
Cmd Driving Pull-Down Level................:Auto
Ctrl Driving Pull-Down Level...............:Auto
Clk Driving Pull-Down Level................:Auto
Channel B
Channel B Timings Settings [Press Enter]
Static tRead Value.........................:6 Auto
tRD Phase0 Adjustmen.......................:0 Auto
tRD Phase1 Adjustment......................:0 Auto
tRD Phase2 Adjustment .....................:0 Auto
tRD Phase3 Adjustment......................:0 Auto
Trd2rd(Different Rank).....................:6 Auto
Twr2wr(Different Rank).....................:6 Auto
Twr2rd(Different Rank).....................:5 Auto
Trd2wr(Same/Diff Rank).....................:8 Auto
Dimm1 Clock Skew Control...................:Auto
Dimm2 Clock Skew Control...................:Auto
DDR Write Training .........................:Auto
Channel B Driving Settings [Press Enter]
Driving Strength Profile...................:[AUTO]
Data Driving Pull-Up Level.................:Auto
Cmd Driving Pull-Up Level..................:Auto
Ctrl Driving Pull-Up Level.................:Auto
Clk Driving Pull-Up Level..................:Auto
Data Driving Pull-Down Level...............:Auto
Cmd Driving Pull-Down Level................:Auto
Ctrl Driving Pull-Down Level...............:Auto
Clk Driving Pull-Down Level................:Auto
Motherboard Voltage Control
Voltage Type.………... Normal
CPU
Load Line Calibration......................:[Disabled]
CPU Vcore..................................:1.325v................Auto
CPU Termination…..... 1.200V*..............:Auto
CPU PLL...............1.500V*..............:Auto
CPU Reference.........0.755V*..............:Auto
MCH/ICH
MCH Core..............1.100V...............:Auto
MCH Reference.........0.800V...............:Auto
MCH/DRAM Ref..........0.900V...............:Auto
ICH I/O...............1.550V...............:Auto
ICH Core............……1.100V...............:Auto
DRAM
DRAM Voltage..........1.800V...............:Auto
DRAM Termination......0.900V...............:Auto
Channel A Reference...0.900V...............:Auto
Channel B Reference...0.900V...............:Auto
Advanced Settings
Limit CPUID Max. to 3......................: [Enabled]
No-Execute Memory Protect..................: [Enabled]
CPU Enhanced Halt (C1E)....................: [Enabled]
C2/C2E State Support.......................: [Enabled]
x C4/C4E State Support.....................: [Enabled]
CPU Thermal Monitor 2(TM2) ................: [Enabled]
CPU EIST Function : [Enabled]  Newbie myself but shouldn't the PCI-e clock be 100 not AUTO |
|
|
|
|
Quote
0.0414sec
0.62
7 queries
GZIP Disabled