ben busy for a night and finally come out with this result

quite happy.

Regards
AceCombat
Republic of Gamers


Attached thumbnail(s)

sorry bro,i dont have so much time for it.
but30 minutes is more than enough i think,cause i dont use 4ghz for daily

the voltage is crazy reading....
i set 1.45vcore but all software detected 0.1v plus,no know why.

all teh rest voltage i forgotten already,now i undervolt my processor and run @ 3.0ghz only

sure,but just a little bit,i think just one unit upper stock.

sure,here u go,attached,but the performance is not really tweaked one.i opened all cpu-z and run it,that's why it should just milisecond faster.

3.4ghz stock vcore and no help if pump more vcore.
but rare gem

so that it's easier to hit high speed with lower fsb,


Attached thumbnail(s)

yup,Ace meimei using the super heavy Maximus II Formula...but the result have to tweak again.

for quaddie i no fully tweak yet,i reaching 500fsb easily.
this week i'll borrow a E7200 from forumer ktek and try try

no problemo,anytime and anywhere but not in ym bed room,i scare u do something bad to me

anyway,how's ur E21?

btw,this is my pc spec that i promised u to show up here

Processor: Intel Core 2 Quad Q9450 Yorkfield C1
CPU Clockspeed : 4000MHz (500*8 FSB*Multiplier)
Motherboard : Asus Maximus II Formula ROG
RAM Model : G-Skill 1000MHz CL5
RAM Capacity : 2GB X 2
RAM speed : 1000MHz, 5-5-5-15
RAM mode : Dual Channel
Cooler : Thermalrigth Ultra 120 Extreme (Single low speed fan)


This post has been edited by AceCombat: Jul 19 2008, 06:14 PM

@OC4/3
enough liao la,i'm not that hardcore la as u know...
3ghz already too fast for me to handle,i'm girl u know....

@enson
mostly it's at the chipset page and at the CPU feature,just turn off them C1E or EIST

sure sure,but i've to oc it back first,all forgotten liao

sure la,the only female overclocker that active here,no more others meimei liao

@fesick.

what mobo r u using?
can u tell us the bios reading,and window mobo utility reading,core temp reading and real temp reading?

and pls show us the screenie,we need to knwo the TJMax

guys,i need some advice here.

can all 45nm user no matter duallie or quaddie report ur temperature here?
so taht we can have a reference that 45nm in working in what temperature in what speed.

deal?

my Q9450 @ 3.2GHz 1.12vcore idle

core temp reading

48c 46c 44c 44c

load
56c 56c 51c 50c

using TRUE and TX-2

for me it's consider very hot,but i'm not sure which TJ Max to follow but i prefer the hotter one.

any idea?

i think the temperature is depend on mobo.

i tried E7200 on Maximus II Formula and a MSI P35 Neo 3,both reading totally different,

@OC4/3
using WC and get that speed is not bad but it still can be pushed to 5GHZ

@fesick
for me,i'll take note about the higher temp so that it's more safe than we use the lower temp to prevent any accident.

OC4/3

dont liquid,use solid batter

currently i'm fine tuning my rig,so have to slow slow tune cause i have exam this few days,but still tangan itch go do some fine tune too.

anyway,will update u asap,no worry about this.

btw,is Q9450 @ 3.2GHz with 1.11vcore consider good?

2.3vcore?
i think it's 2.3vdimm right?
anyway,there might be one stick of them is a bit faulty,try to swap the ram slot.
if the problem still there,u have to test the ram with only one stick and run them in 1066 speed.
good luck in trying

yup,confirmed prime stable with 1.11vcore

@ryudox

unlink ur ram ro fsb ratio.
then run ur ram in 1066MHz CL4,try to push ur ram and u will see some improvement.

i did mine with 1.5vcore only without major tweaking,if tweak here tweak there i believe it can be less than 1.5 for 500*8

Ace lenglui already her MIIF liao lo long time ago.
i break to 520MHz already but forgotten to the screenshot