hey u guys/gals.. may i know how long did u all run the prime from orthos to test the oc? 1 hour? or more?

i got my E6600 running at 3Ghz all the time but nve hit 3.6GHz..

to test for absolute stability it is recommended to test it for 12hours or more...

omg.. what will happen then? i try it for 5 min.. and the temp fly up to 60 within 5 sec and maintain there.. after 5 min,it bcome 62.. i dont know what will happen if 24 hours..

anyway,thanks bro for letting me know

weird wor....u are using TRUE oso so hot? u pump to high vcore liao isit?

waa..even last time i stress my e6550 never reach that high bro..

i dont think so my ram can achieve that high 1:1 ... 1333 for my ballistix is too much...lolzx..

This post has been edited by ryudox: Aug 1 2008, 03:42 PM

how to set the cpu:ram ratio?

u know how to set ram speed?

for example your fsb is 400 , just set your ram speed to 800mhz

so hot?? my e6230 @ 3.5gz only at 62 full load...

no,i mean if ur fsb is 333,so ur ram should be 666mhz.then u can thighter ur timings.

anyway do check this thread.. Oc guide

lemme give ss for cpu-id and temp for idle..








the vcore i set is 1.288.. but in the bios,i set 1.3 sumthing.. ima super newb in oc.. just try and error for now..

This post has been edited by xhacker: Aug 1 2008, 09:38 PM

hmm...try use other software like coretemp or realtemp or everest n see see lor... the one u shown is idle temp ar? 43c with TRUE on idle is kinda

if reading is still high, then maybe u will have to check ur thermal paste spreading n contact of ur heatsink see if it tight enuf i guess....

yeap.. i use coretemp also show 42~43c.. no change..


hmm.. im using tuniq tx-2.. i read about it and ppls said it better than MX-2..

i will check again my hsf.. ohh btw.. my TRUE,i put it a bit senget coz if i put straight,it fan holder will block my top fan blade..

I've used TX2/MX2 and to be honest, both are about the same

using Real Temp program

idle -41d'
load 51d'
vcore voltage i set to 1.35v

i using E8200 OC till 3.46ghz
my memory is like 866mhz

is this ok r? or my temp too high

i personally think most high end air coolers work around the same temps.. and thermal paste.. not much of a difference. 42 to me is fine if there is no aircond, or the exhaust fan is a bling2 version. I have the same issue too

hmm...weird bro..... this is the same proc that uses same tx like u.... at almost the same clock, but the temp seem differ quite alot... as far as i know, the cooler has almost the same ability as TRUE... maybe u can use it as reference.... that guy is on non aircond environment too... but half naked rig tho and he did the test at 3am

http://forum.lowyat.net/index.php?showtopi...post&p=16580244
http://forum.lowyat.net/index.php?showtopi...post&p=16595221

This post has been edited by tkh_1001: Aug 2 2008, 12:24 PM

lol.. i think it bcause i did it at 2pm.. hot,i can feel my is hot.. at 3am,i got 36~39c temp with 3.30g.. hmm..

after i read and see his post,i think i need to re apply my thermal paste.. and check back on how i mount my TRUE.. or maybe xigmatek is better than mine? hmm..

currently im running orthos.. 15 hours pass.. i tihink my oc good edi.. 61c with orthos..


EDIT : im using cooler master silent uv fan.. low cfm..



This post has been edited by xhacker: Aug 2 2008, 09:58 PM