Welcome Guest ( Log In | Register )

Bump Topic Topic Closed RSS Feed
3 Pages  1 2 3 >Bottom

Outline · [ Standard ] · Linear+

Unifi Official TM UniFi High Speed Broadbrand Thread V6, News: RM200 for installation after Sept

views
     
alextong8386
post Aug 3 2010, 08:37 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


Hi Sifu,

May I know did anyone conceal your internal wiring for Unifi fiber optic cable? Normally, for a 2 storey link house at Shah Alam with already underground copper telephone line, where will the fiber optic cable being install? Ground floor or 2nd floor?
alextong8386
post Aug 4 2010, 09:26 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


Currently I contact my home alarm system direct to my copper phone line. What can I do after install Unifi and discontinue my fix line phone service? Do I need to keep my exiting fix line phone?
alextong8386
post Aug 6 2010, 12:32 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


Can we connect our desktop direct from Fiberhome unit using LAN2 without going through the D-Link DIR-615 G1.
alextong8386
post Aug 6 2010, 08:21 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


May I know what is the advantage for using the VLAN Bridge using the D-Link DIR-615 G1 router? If this D-Link router on fried, we still cannot online using the customize router.
alextong8386
post Aug 6 2010, 11:20 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(aliftaufiq @ Aug 6 2010, 10:53 AM)
Guyz,how many days does it take to terminate the old fixed line+streamyx??
Submit my termination form last monday but until today still can use..Huhu
*
Normally is 24 hours. U need to follow up with TM CS
alextong8386
post Aug 6 2010, 04:05 PM

New Member
*
Newbie
0 posts

Joined: Mar 2010


Do we need the Aztch 1 Gigabit home plug? Will Aztech 200MB home plug sufficient? At the moment the IPTV bandwidth is only 8MB.
alextong8386
post Aug 7 2010, 10:16 PM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(Traveler @ Aug 7 2010, 03:44 PM)
Unifi 20Mbps installation done. IPTV not done as I wanted the new modem to be installed in my home office where my router (did not want to use TM's router) and switch were located, while I would want to watch TV in the living room or bed room, and not in the home office.

Secured the TM router using the advice given here.
Reconfigured the TM router to be a VLAN bridge (as per instruction in the above link), and am now using my router instead.

Did a few speed tests, see results below.

KL server:
user posted image

Singapore server:
user posted image

HK server:
user posted image

Tokyo server:
user posted image

London server:
user posted image

San Francisco server:
user posted image

New York server:
user posted image
*
What different using the TM router to be a VLAN bridge vs own router? It still need to go through the D-Link 615. If it break down, we still cannot go online.

alextong8386
post Aug 8 2010, 02:07 PM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(vergas @ Aug 8 2010, 11:12 AM)
After using another router, now I can get full and stable speed for torrent.
Thanks all for the guide. Looks like another router is really needed if you want to torrent a lot.

» Click to show Spoiler - click again to hide... «

*
What router do u use? Do you still use the VLAN bridging via D-Link 615 that was provided by Unifi? Is it same wiring recommendation as the athena website.
alextong8386
post Aug 9 2010, 03:02 PM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(shojikun @ Aug 9 2010, 01:15 PM)
aiya... currently house is installing, and got some problem at the terminator there sad.gif on a side note, for VIP5 and VIP10 shouldnt have any bandwidth cap or something  brows.gif
*
Do u conceal the all the unifi internal wiring by the TM contractor? How much there charge?
alextong8386
post Aug 9 2010, 05:26 PM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(shojikun @ Aug 9 2010, 03:07 PM)
currently FOC.. o_O"
*
Really, some mention TM charge RM250 or more (depend for the length of the wire) for concealing the unifi wire. BTW, how their workmanship of concealing of the wire in the wall.
alextong8386
post Aug 11 2010, 08:43 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(vergas @ Aug 11 2010, 08:11 AM)
Get a custom router and do bridging, that will solve most of the problems.
*
What a customize router will help via VLAN bridging? It still connect to D-Link DIR 615. Since D-Link CIR 615 is the cause of the problem why not we just replace it?
alextong8386
post Aug 12 2010, 05:55 PM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(pr0di9y @ Aug 12 2010, 02:46 PM)
Sup gais, 1st post in many years L O L...

Anyway just got my UniFi setup today with the HUAWEI modem instead of the ZTE biggrin.gif

Going to setup my WRT54GL to be the main router instead of the Dlink DIR-615. Wish me luck...
*
The Dlink DIR-615 is a more advance router as compare to Linksys WRT54GL. It has a faster CPU, more RAM and more advance feature such as VLAN which can provide better security feature if it is configure correct as compare to old WRT54GL.
alextong8386
post Aug 14 2010, 06:59 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(auronthas @ Aug 14 2010, 02:20 AM)
I am noob in telecommunication network, have few questions as follow: -

a) My current router is of Linksys WAG120N Wireless-N ADSL2+ Modem Router, is it compatible to TM DIR-615 G1 routers?

b) Plan to upgrade from my current Streamyx Combo (RM 110) to UNIFI VIP5, it's still under 1 year contract, possible to upgrade without breaching the contract?

Thanks in advance
*
You cannot use a ADSL modem router to setup unifi. It is becos it do not has WAN port. You need a pure wireless router.

Yes, you can upgrade ur Streamyx combo to Unifi.
alextong8386
post Aug 17 2010, 11:56 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(auronthas @ Aug 17 2010, 11:37 AM)
I have just registered with TM UNIFI yesterday, upgrade from Streamyx Combo.

I was informed, my current telephone number (8062xxxx) will be changed to a new assigned number (8051xxxx), do you have the similar scenario?

My current house is double storey terrace with overhead telephone pole at backlane; I have few questions as follow: -

a) How does TM going to lay fibre to my house, ground floor living room from the backlane, will there be a major hacking work?

b) Anyone installed at 1st floor where hacking work is minimum for d/storey house?

c) I have house alarm connected to my existing telephone line, will there be extra charge if I ask TM contractor to split a tel line to the house alarm control panel?

Thanks in advance for replying.

Auronthas
*
It depend on your expectation if you want to conceal all your wiring in the wall or not? If not, there will install all the wire in a plastic casing. Even without hacking, it will not very nice also. I will recommend you to conceal all the wire in the wall. Make sure you get someone who is expert on this conceal work.

As long as you connect the a RJ11 line from Huawei fiber modem TEL1 to your telephone point. All your existing telephone point will be connected by VOIP which include your house alarm. You can DIY.
alextong8386
post Aug 17 2010, 02:12 PM

New Member
*
Newbie
0 posts

Joined: Mar 2010


Has anyone use the Buffalo WZR-HP-G300NH wireless router before to replace the D-Link DIR-615 wireless router before? Can this wireless router link direct to LAN2 at the Huawei modem base on pr0di9y recommendation. Can this wireless router flash with DD-WRT 3rd party firmware?
alextong8386
post Aug 17 2010, 04:02 PM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(wiraone @ Aug 17 2010, 03:45 PM)
I'm using it right now, flashed with the latest release of DD-WRT and was previously running on DD-WRT. There is no VLAN tab in DD-WRT implementation for WZR-HP-G300NH, so, it couldn't replace the DIR-615 entirely. I'm currently using it as AP & router by setting the DIR-615 as network bridge.

Anyway, it seems UNIFI charges us upfront eh? Just received my bill, they're charging me for last month and this month bill, and that is close to RM300.. arghh..
*
Can we use LAN1 at Huawei modem for DIR-615 to be link to IPTV and LAN2 at Huawei modem for WZR-HP-G300NH to be link to internet and VOIP.

I do not plan to use DD-WRT firmware for WZR-HP-G300NH. I will just modify the setting for Huawei modem in order for it to support direct connection for all the 4 LAN port.
alextong8386
post Aug 19 2010, 08:25 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(cafee @ Aug 18 2010, 04:54 PM)
Hi, I just got my Unifi yesterday
HUA WEI @ LAN1 ---> Unifi DIR-615 --> TV
HUA WEI @ LAN2 ---> Personal Router --> PC
Personal Router is also an old Dlink DIR-615 B2 (UPNP enabled and port forward done -> heck even if I DMZ my PC, I still face problems)

I haves problem with port forwarding on BitComet : Listen Port Blocked

And  connecting to the DC++ Hub , I also face the same problem - connection timeout - due to port forwarding issues.

I have done all the port forward and turned off all firewall and antivirus.
I understand that  the guide did mention that NAT would not work as planned.

anyone found a solution to this yet?
*
Hey,

Is VLAN bridging using DIR-615 method better or connect direct to Hua Wei @ LAN2 better?
alextong8386
post Aug 19 2010, 10:48 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(billytong @ Aug 19 2010, 10:29 AM)
Hey guys how long does Between the day you applied Unifi to the day they come to ur house to fix ur stuffz?
*
1 - 2 weeks. It depends on which day u choose. If Sat & Sun only, you may have to wait 2 weeks. And also it depend on the Unifi demand at ur area.
alextong8386
post Aug 19 2010, 06:00 PM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(Red Maniac @ Aug 19 2010, 05:42 PM)
There are getting more and more ppl signing up for the Unifi service.

In fact, when I called TM at 6:30pm yesterday, to enquire for the installation appointment, the earliest date available is on 1st Sept.  Today at 2pm I called to fix the appointment, the earliest available date is 2nd Sept  sweat.gif .  I also been told there will be no installation from the 7th to 12 th Sept due to Raya holiday.  The installation charges will be imposed from the 16th Sept onward.  Better hurry if you're still deciding to use Unifi.
*
How much installation charges will be impose by TM after 16th Sep 2010?

alextong8386
post Aug 20 2010, 01:04 AM

New Member
*
Newbie
0 posts

Joined: Mar 2010


QUOTE(calvin92 @ Aug 19 2010, 09:13 PM)
at least 300. But i have a feeling they might not do this and so call extend the promotional period. its common sense that putting an installation fee will just put people off subscribing and it will be a waste wiring up the national when little people use it. if they already wire up your street why make it difficult for people. but yet again i do not know wat TM is up to BTW
*
Why some says TM charged them almost RM1.5K for installation in their first bill. Now should be FOC right during promo period?


Added on August 20, 2010, 1:10 am
QUOTE(AMDAthlon @ Aug 19 2010, 10:10 PM)
lol..mayb that time your place not supported yet? whistling.gif

Anyway guys.. any suggestions for Router to change TM DIR 615?

What brand/type of router is good?
*
Buffalo WZR-HP-G300NH is a most power wireless router at the moment in term of hardware spec. Even more advance than Linksys, Belkin, D-link. It also come with a very attractive price @ RM259 from compu-zone, Low Yat.


Added on August 20, 2010, 1:13 am
QUOTE(wiraone @ Aug 19 2010, 03:09 PM)
Sorry, didn't really read previous threads .. when you said WAN PPPoE profile, does it mean that you made the BTU as a router? Is there anyway that we could use LAN2 as a network bridge or something? I mean, all the non-IPTV traffic going to LAN2 while only IPTV traffic going to LAN1? I couldn't find any english manual on the net, there is one in Chinese .. but surely, I don't understand it at all smile.gif

For me, my WZR-HP-G300NH is currently running on DD-WRT and I guess my backup will be to set it up as per rizvanrp's DIR-615/DD-WRT.
*
Which website u get Chinese setup manual? Mind to share, I am interested to have a look.

This post has been edited by alextong8386: Aug 20 2010, 01:13 AM

3 Pages  1 2 3 >Top
Topic ClosedOptions
 

Change to:
| Lo-Fi Version
0.0711sec    0.36    8 queries    GZIP Disabled
Time is now: 2nd December 2025 - 09:34 AM