cpu id shows it at 3.2 bro
correct me if im wrong

oops bus speed is 200
multiplier is x16

---

Added on August 8, 2010, 2:57 pmbtw prime95 run an hour d
should i stop?

ran prime95 for almost 2 hours..had no problem..
so should be stable rite?
up d cpu bus?

everybody got new arch already. me still have my 3800+ F3 windsor with me..hahhaha...long time left OC thinggy....now settle with lappy only...

That 1500mhz cl7 and 2000mhz cl9..u talk about Kingston Value Ram right?
owh ic..that ram what chip eh?
so i guess to start ram tweaking need thuban + 800 board.. so will unleash the true potential or the ram (in amd la).. haish.. it will always be a prob for me when it comes to money   

all cores la..see like now im running all cores no problem
but when i switch off my comp and later on it wont run
i have 2 go 2 bios again and do everything all over again

ahahaha y u asking me
ok this is how it goes

when im using 4 cores it is stable no problem at all
but everytime i off/restart comp i will have to use 2 cores 1st
go into windows...reboot...den go to bios again..set it to all cores..
den back to windows...and no problem

any1 has had dis b4?
is my proc unstable o sumting?

i didnt notice...it goes by 2 fast for me
the bios did save the setting..
what happens is
it will say
"unleashed mode failed"
den press f1 for setup and f2 to run on default 2 cores..
but if i go straight to setup and adjust everything again,it wont work after reboot
i have to go into windows with d 2 cores,reboot den go back 2 bios and do everything again
den ok~
haiyooooooooo~         

haha..u mobo same like me what..i bought this proc on april..the different only ram..i got this issue last time but worst..test prime95,it stable but next day boot up,give me BSOD..i guess my ram timing to tight,then loose it a bit..then ok till today..what is urs RAM setting btw?..

ahahaha dats d problem bro....
any ideas ar?

BSOD????
i only noticed mine saying unleashed mode failed
haha
and how do i adjust my ram timing???
help help help         

den??  update bios?
bios version is 0501

cpu was always stable i think
the problem was the unleashed mode sometimes failed
but when it does work the cpu was OK..ran prime95 for 2 hours and didnt fail me
after updated bios tried restarting/off on pc and the problem was gone

     

thank u bros..really appreciate all the input and help from u guys

and yes, when i decide to OC i will make sure i have a better cooler and casing 

X6 1055T 4.3Ghz is sweet already

colgate total... it was done on a cogage true spirit w/ 2 cm 90cfm led fan @ push-pull. mobo used is cheapo 88td-v evo /usb3. 
not, ven x still in d box, no time to put it on yet. yup, it was a 125watter. from what i read thuban integrated thermal sensor some how gives wrong readin, so dun get too excited w/ d low temp... 

yalor bro... sayang mau pasang... will use it only after u post d thuban chip to me... 



finally, gskill flare's record has been equaled. 

[attachmentid=1716673]
there's no way to prime stable @ 4.3GHz w/ my kinda skill & coolin mate... 

Depends on cooling i believe, if ur on a good WC i think 4ghz ~ 4.2ghz should be do'able i think
For air cooling we tend to have to stick 4ghz and below..

65c still okay~~
If you wanna go cooler, go find yourself a 95W TDP X6 1055T

We are talking about the CPU temp
Not the Mobo NB temp plus u didn't mention it in your earlier post