price is negotiable ..

sleeves kena biayai sendiri ye

plez lah dunnot put summore pictar...
really venomous & killin' me.....
batuk berdarah hamba menengoknyer....tdk tahan
kenot stand it anymore......

ambik tongkat ali.. make u stronger

bwahaha.maybe this is the time for you to move on la bro.. ..come and i welcome u to the club..

dom ko tu nice la.. ..dah try 2000mhz and uncore 4k x..??..rugi x try oo...

oit... dah siap rupe nye.. hahaha... drain tak ade pun..

blh buat ker on air? kalo boleh kene ler ko ajar aku...hihihihi
tapi kalo on WC,kene pospon dulu ler....kang tebakar plak moboku tercinta ni...kikikiki

*ko ade ushar x pricelist yoongkeen? demn rege R3E dah drop RM1350....kureng sawan btol la...
WC set up will b on next extraordinary phase apgred kalo pitih ku blana kona
ni last warning aku kasi sama ko...kalo ko brani letak pictar2 yg powah2....aku....aku....aku.......aku..........aku
aku ngadu ngan bini aku.......wwwwaaaaaaaaaaaaaaaaaaaa

This post has been edited by huzzLEE_82: Aug 5 2010, 08:51 AM

wat size u use for revet bro?

@ sopen2003..

ade..jap2..



akw bwat pendek je..coz, case tu bukanye besar pun..huhu..ngan wayar casing lag, berselerak kowt..

@huzlee..

yeahhh.. .akw tunggu ko nye setup skang.. .mane lah taw..die CF 5870 + full block pulak kan.. ..wakakak..boleh on air... .just make sure temp nb dalam 6x okay lagi...

tak cantik pon
buat la cantik2 sket baru tergoda

This post has been edited by pc-mafia: Aug 9 2010, 10:59 AM

hahaha.. ..hati membare gak ke.. ..meh la dtang sini tgk..

lagi lagi...update lagi yang baru2 ni...sudah berlampu ke.hehe

bang,

does your water enough pressure flow to pump?

bcos saw your pump put at higher than reservoir...

ekeke..so far, i have no issue regarding the pump placement..the Q-Max for EK 4.0 is 800L/Hr which i considered quite powerful..my tube is not too lengthy.thats why maybe the pump still can push the water..

.btw, how to check whether there is enough pressure or not..?..

the pump place is still get pressure i think.. cz the resevoir of coolant/water still carry enuf pressure for the water go into pump...
example is when u mandi the tangki tank if u put a tube at bottom and sambung go to middle (same as TS picture show reservoir as tangki tank and pump be the Tube) the tube confirm got water comeo out =) due to high pressure in the tangki...

correct me if i worng

i have adjusted the pump at the bottom..

coz, it is actually hard for the water to go trough the pump with the previous placement..



got my new CM 90 CFM red led

huhuhu... caya la bro ..jiwa terbakar ni.. berhajat jgk..modal brapa untuk bikin watercooler ni??

ekeke..ade la dalam 1.5 k kowt.. ..tanye bro vlad.. ..mane la taw, ade promo sempena raye ke.

bro that's y i ask u, your reservoir water enough pressure to pump o not..

since ur 1st setup is pump place higher than reservoir.. by right pump should place lower than reservoir....

---

Added on September 9, 2010, 7:38 pmoh ya... bro dont place your inlet and outlet at the same way. it will caused your water cant circulate...

the reason is once water in your reservoir, immediately out..



This post has been edited by subrok007: Sep 9 2010, 07:38 PM

@subrok007

when the first time i place the pump on the dvd/drive bay, actually it does have no problem with it, because, the water level is still higher than the pump, the water still went inside the pump,..

but, i start to realized that, the air pressure in the loop higher if the tube was empty..means that, if i throw out the water at the first time, and start to refill it again, the air has fill in the tube..resulted the water can't went through the pump..

Nice build , must learn from you la...kalau rezeki baik..next build i will WC