let says that the result that i got from d gogar'optimizer is divider 166

how to set it in the bios...

cannot see anything relatesd to it in the setup

sifu please help me.. see my rank in first post.. doesn't it looks bad? 3200+ is much slower than other 3000+.

how to set it? it should be called something like DRAM frequency or divider .. look for one that gives u a few options like

100
133
166
200

in bios

actually u can see how to set the bios using the calculator.. use the numbers that it stated as u have insert the desired speed.. dunno if it is true or not.. in my point of view ler..

Here's my latest n it's maxed out oredi. It's at 2.7Ghz Prime stable at 1.6Vcore. Tried 2.8Ghz n the prime failed after only 2 minutes even with 1.7Vcore.





This post has been edited by ianho: Jun 7 2005, 02:42 AM

hehhee.. ur guys are so good coz replying to nooobsss so fast...

cheers to know if any chaplang psu like to me to reach 250htt

ianho.. blow a fan into ur case and try again..

what's the best temperature monitoring software other than core center

babyelf i cannot find nothing with dram divider

jus found this fsb startup


This post has been edited by dreamkiller: Jun 7 2005, 01:40 PM

rezzz!.. any information about divider for my motherboard........

ask those that have ur board.. i duno what it's called on ur bios

check every settings and see.. should have one with 200 166 133 100

Blow fan 4 what? The room temps for the past few days at 33-35C man. Anyway, how does the fan help a WC set up, cool the PWM?

This post has been edited by ianho: Jun 7 2005, 02:07 PM

Don't play play with chapalang PSU man. Sooner rather than later it'll blow up. If ure unlucky, it will take ure mobo n chip to heaven too. Then u'll only have a mofo of a mobo. Hahahaha. Nowadays reasonable PSU only bout rm200 so go get 1 if u like OC. Don't wait until it happens.

gonna quit from oc unti i get a good PSU hehehe.. thanks ianho for

advising me... psu's realibility is rated from its rails isn't it..

U don't hafta worry about which to buy. Just make sure it's from Antec, Enermax or Tagan then sure good. Also make sure u get at least 30A from the combined 12V rails. Don't buy any of the local brands.

yea.. cool the dimms and circulate the air better.. lower chipset temp and mosfet temps.. try and see..

my winchester 3000+ also cannot go higher then 2.0
not really know how to set the divider also.....

raise the HTT from 200 to what ever value u want to O/C...save settings...reboot...see what happends...if got tittttt titttttt tittttt sound then ur ram has problem wif the speed...so press insert while booting then lower htt see what happens....

ALWIZ REMEMBER

while juz raising HTT without touching other settings u might wanna know that ur HT Speed is already more than 1000mhz...the instability would really easy to happend....its better that u read through 1st on how to overclock an AMD 64 bcoz it is slighly diffrent..these are some tips on how to overclock easy..(but not too high)

vcore 1.55v
vdimm 2.8v
RAM latency 2.5/3-4-4-8 (try this first for beginners)
RAM Speed 200
HT X 4
HTT/FSB = Raised to 250 by 10 or 5 increments from 200...
pci/agp lock = 67/34

Hope this helps...

and about PSU...u should never in the first place even think of using it...throw it away...coz its like a time bomb which waits patiently for the time to blow up....get Acbel coz its cheap...get OCZ or Antec NEO or TTGI coz its powerfull...get a Ultra x-connect coz its cun....

The core center try to download the latest version which is......i dunno...my MSI Neo2 blew up last 2 months....so i dunno any updates for MSI...

Dividers setting are usually at the DRAM Setting at the Advance Chipset Settings or Advandce Settings

it usually sits on auto or 200....

i already use that setting. but i use ddr333 ram (BT-J). i increase through clock gen.
but still cannot stable above 2.4G

My Venice 3200+ seems to be a total failure.
Only can get 2250 (250x9) 1.50V.
What seems to be wrong?
Using Asus A8N SLI Deluxe
HTT multiplier = 3x
RAM divider at 333