yep do it on bios la... hehehehe hi antonio...







btw if pcrazy pass by here... HAPPY BIRTHDAY hahaha 24 ker?

HIHIHI...bestday dierk ker???hahahaha....
ok back to topic....

do it from bios...easier to find troubleshoting...

ohh, thanks, will try later

Should we open one more category for Opty ranking?

The first post almost 2months no update already....
and all the time i was using air cooling, not water...

The first post almost 2months no update already....
and all the time i was using air cooling, not water...

some prob here... was running 2x 1GB at 240Mhz then swapped 2x512MB to do some testing.. after swapping the 2x1GB back... now slot 2 seems to be dead... so using slot 3 & 4 now.. but cant do 240Mhz anymore...... only 220Mhz now.. sys spec as in sig

tried CMOS clearing, start/restart 10x times... still at 220Mhz

This post has been edited by jsnkok: Dec 11 2005, 04:54 PM

Hi. Have you tried switching the rams in the same slots? And also, might consider the trick here
Good luck....

if rams in slot 1 n 2 only 1GB is detected.. switched the ram sticks around and still the same.. 1GB detected during BIOS mem check... so now using slot 3 n 4. So the rams arent faulty or anything... but then again i cant do 240Mhz anymore....

Could be the slots there. Best work at 1 & 2 (purple, green) so try booting with 1 stick at slot 1 first, after that try the second stick. If it succeeded, try putting both in.... GLuck

well.. tried that... not working.. so i deduced that slot 2 must have just died on me...

just found out the cause.. one of the pins in slot 2 somehow bended.. i have no idea how it got bended by just changing rams.... sigh.. and slot 3 n 4 is not that good... as reported by other users as well.. guess i'm now stuck at 225x9.

guys...i m very new to overclocking with AMD...so here r my screenies...any comments?

i found out that when i m using only 1 x 512mb RAM,the timings for super pi is much less slower than timing when i use 2x512mb...

currently using air cooling..with xp120...n using only a stick of 512mb RAM(mine is nforce 3..only single channel) with 3.1 volt..thats d max from my mother board...

n using 1200rpm fan only...n my rig is very quiet...so any comments?



can make it into the top ten?socket754...

every comment will b deeply appreciated...

This post has been edited by pukarix: Dec 15 2005, 12:27 AM

my overclocked sempron 2500+
Cooling : Artic Freezer 64
Vcore : 1.52V



hope it is not too late to join d OC DATABASE

This post has been edited by flamming: Dec 15 2005, 03:03 AM

Woohoo.

http://valid.x86-secret.com/show_oc?id=58174

:S

cpu-z validation is not enuff.... show some prime!

and the load temp too..

Yeah, I have to work on those. I don't even know how stable it is at 2.76GHz. Using stock AMD cooler.

A question: How high can Corsair XMS CMX512-3200C2 Rev 6.1 be pushed? I've gotten up to 3.0V, worried to go any higher. Can't boot into Windows XP properly with DDR above 230MHz.

*sigh* Need better cooling.

noobs here.... i oced my system to 2160mhz and it was quite stable where i could run prime test for 2 hours... so i start cranking 100mhz more and then my computer goes crazy, so i clear the cmos but start from this whenever i adjust the cpu htt,it seems that my system was not stable anymore and i could just tweaked the fsb using clockgen

sorry for this troublesome anyway..really need help(i know i used a kapcai psu but i was not hoping to reach sky high oc...just wanna touch 22xx with high htt

This post has been edited by dreamkiller: Dec 23 2005, 12:52 AM

2 important and simple steps :

- lower your HTT/LDT multiplier (should be 5X default, set it to 4 or 3)
- lower your rams/fsb multiplier (set it to 166 or 133)

the options might be called something else on your mobo though