hehe... already figured that out....hehe...nice burning u got for this ram...thanks man

btw....why in memtest86+ this ram can go 260fsb 2.5-3-3-7 2 hours no error...but still cannot boot into windows lorr..... using multiplier x8...hurm..the highest can boot into windows is at 256fsb only....

wanna try doing some test at 275 3-4-4-8 1T on my ultra-d tonight....

oledi tried 2-2-2-5 1T 200fsb last night....but cannot boot into windows lorr....got error message summore after the post screen....uhuk uhuk...

my dfi do lock the true potential of my ram....uwa uwa..

hynix does not do 2-2-2 ler... everybody knows that

ho'oh betulla soulfly...huhu silly me... should test 2-2-3-11 1T instead...haha silly me..

on 1T only...but on 2T can...

ehh how to know my ram is hynix
if look at the box ... i can see hyn there
is this call it hynix
dont ask me why i dont check at ram chip
it's bcoz i already put heatspreader
and already lock it...hard to open

mine can!

only with mantarays xt 2t bios and 2.8v ! 2-2-2-11

can boot and runs games like normal,,, but faster.

yep sure can!!!
as lond as u plant the ram on nf2.
same thing on asus a7n8x-e deluxe.
set it for daily use no problem

edit : lond = long.

This post has been edited by rzonealley: Aug 22 2005, 03:04 PM

@ what speed?...

no point running 2-2-2-11 at 2T when 2-3-3-11 at 1T gives better bandwidth

can system as my sig use 1T

coz i heard that doublesided can't use it!

HYN - guaranteed to be hynix - if you bought it new and installed the ram yourself

thanx man

Anyone can post the stock timing configuration for KVR in A64 Tweaker for me plz ? Just take a screenshot of the a64 tweaker , but in stock lar .

if ddr400 must be 3-3-3-8

ive seen some box got hyn but relabelled Kingston inside.
the physical same like hynix.
Overclock oso same like hynix but dunno why it relabelled.

hehe .. good ram you got over there if can reach 275Mhz stable.


the highest i got for my bt-d43 was at 280Mhz benchable ... but now i can't reach tat speed anymore after i update my bios. sigh.

huhu...test results failed...still stucks on 259fsb...can boot into windows..but vey unstable liou ..the highest can go stable is at 256fsb..

hehe .. manage to get my ram running 2.5-4-4-10 1T @ 3V

benchable at 282Mhz
bootable at 284Mhz

on my KVR bt-d43

Genie BIOS Settings:

FSB Bus Frequency - 282
AGP Bus Frequency - 67mhz
Clock Spread Spectrum - Disabled
LDT Downstream Width - Auto
LDT Upstream Width - Auto
LDT/FSB Frequency - X 3.0
CPU/FSB Frequency Ratio - X 8.0

CPU VID Control - 1.500v
CPU VID Special Control - Avove VID * 104%
Chip Set Voltage Control - 1.80v
AGP Voltage Control - 1.70v
DRAM Voltage Control - 3.00v

DRAM Configuration Settings:

DRAM Frequency Set - 200
Command Per Clock (CPC) - Enable
CAS Latency Control (Tcl) - 2.5
RAS# to CAS# delay (Trcd) - 04 Bus Clocks
Min RAS# active time (Tras) - 10 Bus Clocks
Row precharge time (Trp) - 04 Bus Clocks
Row Cycle time (Trc) - 10 Bus Clocks
Row refresh cyc time (Trfc) - 17 Bus Clocks
Row to Row delay (Trrd) - 03 Bus Clocks
Write recovery time (Twr) - 03 Bus Clocks
Write to Read delay (Twtr) - 02 Bus Clocks
Read to Write delay (Trwt) - 03 Bus Clocks
Refresh Period (Tref) - 4708 Cycles
Write CAS Latency (Twcl) - Auto


DQS Skew Control - Decrease Skew
DQS Skew Value - 128
DRAM Drive Strength - Level 1
Max Async Latency - 08.0 Nano Seconds
Read Preamble Time - 06.0 Nano Seconds
IdleCycle Limit - 256 Cycles
Dynamic Counter - Disable
R/W Queue Bypass - Auto
Bypass Max - 07 x
32 Byte Granularity - Disable(8 Bursts)


This post has been edited by shadow_dweller: Aug 24 2005, 01:54 PM


Attached thumbnail(s)

can ur setting can be applied on my nf4?....huhu hynix can got lidat on DFI is like a wet dream lor...haha