Just for your information DT-D43 on KVR mostly capable of 260+ at 2.5-4-4-8 if not 2.5-3-3-8 @ 1T. I believe yours had more potential, seek it slowly.

This post has been edited by PCcrazy: Mar 30 2006, 08:10 PM

Trying ^^ but somehow I need to upgrade my PSU to 450W, system running power hungry now...

yupzz.. loosened adi.. still cannot.. dunno why.. after BIOS cannot load Windows.. whyyy..

hail to forumer
im newbie
last time i was bought pczone rm300 last 2weeks d43
i m not sure wat vers. 1gb ddr400 pc3200
my timing 3-4-4-8
268mhz x 9 = 2.4ghz (333)
cpu amd64 754 2800++ (2.4ghz)
anyone can suggest me to improve the oc
i can reach to 2.5ghz but to scared if the ram can burn...

Wao,your RAM can reach 268Mhz at 3-4-4-8.That's consider very high power already. You are setting the RAMs running on what voltage?

no supprise.....my apacer can do it better

Thats a good dt-d43 on your apacer

@^KamilskaZ^ APACER with DT-D43 chipset.Very hard to get it in the market.Dam lucky you are.Nice o/c you have.

My Team XTREEM DT-D43 maxed out at 255FSB @ 3-3-3-8 can't push any higher

yeah damn mine....now im looking new twinmos more value than kvr at some place at melaka.

anywone now twinmos pc3200 CA4T chipset inside?

wooor my chip type is ct-d43
so im dissapointed of that cause its hard to find the dt-d43
my mobo is abit nf3 n the max multply is 9..
so my vdimm is 2.8v
cpu 1.6v
ram comformity 1.27
hypertransport 1.25v
mhz is 166
idlw temp system is 35c and cpu 38c
full load system 44c n cpu goes to 46c -48c

my rig
amd64 754 2800+ (2.4ghz)
mobo abit nf3
gc ati 9600xt little oc
hd 80gb sata seagate baracuda
cpu cooler zalman 7000 try to find 7700 but finish

Actually i am trying to look for DT-D43 chips for long time already.Somemore you got them on APACER.If you bought your new twinmos RAM,wanna sell your apacer RAM?If do please let me know.I am interested on your RAM.

no doubt ur ram can go 280mhz at 3-3-3-8.pm me if ur want to sell.

do u think D43 can run 2-2-2-5 at 133clock??

Skylinestar: I guess shouldn't be a problem

as i mentioned earlier.

i have already bought the bt-d43.

i paired it up with my dt-d43.

so both running on dual channel at 210 , stable.

512mb DT & BT-d43 running at 210 ( 2 - 3 - 3 - 11 )

i cud go as far as 221 but not stable while priming

the cpu-z is attached.

i'm trying to go higher..

or is it my cpu limitation ..

AXP 2200++

plz inform where i will find dt-d43
1gb ram whre place n price the latest one
cause mine use ct-d43 can push to 267 with 333

Try lower the timing to 2.5-3-3-8, used to do 240x9 on my AXP 1700+ on that timings, but i guess maybe your BT-D43 is holding back your DT

will do that...

and try

Typical standard procedure for overclocking the hynix based chipset:

Set the timing at 3-4-4-8 to begin with and scale the frequency until errors show out. When the limit is found try to adjust the timing in memtest to 3-3-3-8 to see if the same capability exist.

Reason as per suggestion : Most of the hynix show true colors at this timing. 3-3-3-8 is okay but results differs greatly, some 3-3-3-8 would go only 215 and some would go as far 260. But most 3-4-4-8 would go 250. So I suggest if you are new to this, begin with 3-4-4-8.

My advice is to always start overclocking from the loosest to the tightest, the same applies to proc and graphics card.