dah tukar gambar nampaknya..

i week to go......but i did'nt do anything yet !!!

Mr. choycp sudah beralih arah nmpaknye..hehehe

Dah kena racun budak cina kat TU maaa

ive been converted!! hope im able to give some pressure to the MS PRO ppl....

juz came back from TU~ having fun in TU today~~ new layout is fun...so many corner...

this MS PROer is pressured oredi..hahaha
nvmd, just wanna race for fun..hopefully i'm able to go for this race..

oit 620 ade lagi ke x?

I tried this with sprint dash motor, managed to get 19-20 seconds only for the previous track.
Really don't know how to lighten it.

-super speed gear
-gear bearings
-axle bearings
-grease added
-light centre chassis
-bumperless front and back chassis
-large diameter wheel
-eneloop NiMH batteries 2000 MaH...



This post has been edited by Beans: Jun 19 2010, 12:13 AM


Attached thumbnail(s)

the car did't look like a car using sprint dash motor~?

BEANS>
its because u use sprint dash on MS PRO thats why...
kalau 2 wheel drive, lagi lagi rear wheel saja...cornering slow.

btw, have you tried to use other roller ball bearings e.g 19mm, 9mm? maybe u should change to plastic wheels as it is lighter, and of course clear cover. this should be able to shave off at least 1 sec off without major mods.

clean the bearings with RC cleaner...and forget the grease lah. try using zippo lighter fluid for lubrication.

---

Added on June 19, 2010, 12:37 amthats what i thought...how come mspro can put sprint dash wan

This post has been edited by choycp: Jun 19 2010, 12:37 AM

ya, you are right, it is not supposed to be equipped with sprint dash but hyper dash is slower after trying it out, so i tested on sprint dash...it worked afaster (=
erm, 19mm and 9mm, i don't have that bearings yet. Are they better?

Ya, clear cover is another option to improve the speed...zippo lighter fluid...gotta check it out what's that first but does it dry fast like alcohol?

zippo fluid dries quick, something like alchohol. and no problems of staining the track too...

i suggest trying out the 9mm bearings, theyre cheap and prettty fast. not to mention that u can 'upgrade' the bearings by fitting a 520 bearing inside the 9mm.

maybe your HDpro is dying out on u, change to a new one and test again.

oh my god, zippo fluid dries fast, how to use as lubricant???

in other words, run the bearings dry. when u keeping the car, oil the bearing so it doesnt rust. tq tq

ya choycp, if it dries fast, how is it going to smoothen the gears?
well I have 3 hyper-dash pro.
one is totally clean.
one is already opened cleaned with hexane(a kind of volatile hydrocarbon), and the end of motor bells are lubricated with oil.
one is sprayed with alcohol cleaner through its hole and the ends of the bell are also lubricated with oil to avoid squeeky sound while running.

BUt the one which is opened performs the best, but yet still can't be as fast as sprint dash )=

---

Added on June 19, 2010, 1:07 amerm, sorry, you mean the zippo fluid is for motor or bearings?
because I didn't use anything on the bearings, just the gears only.

This post has been edited by Beans: Jun 19 2010, 01:07 AM

rm100 per pack how many u want

sorry i mean per pcs so its rm200 per pack

take the metal rims out . they are bit heavy

just finish you party ???

btw, i suddenly got an idea to use 850..hehehe

---

Added on June 19, 2010, 3:23 amdavid watching england??? i am btw~~hahaha....

---

Added on June 19, 2010, 6:29 am
if these are the polycarbonate body ... both body shocking me !!!!!

hong kong already have it!!!!! unbelievable !!!!

---

Added on June 19, 2010, 7:26 amthis is why we usually tape our track with a duct tape!!!


This post has been edited by szngszng: Jun 19 2010, 07:27 AM

Erm, 620 is for what use???
why so expensive one compared to normal bearings?

This post has been edited by Beans: Jun 19 2010, 11:26 AM

because its a specialz spacerz creatz byz tamiya . check davids spacers pic for more info