Welcome Guest ( Log In | Register )

Bump Topic Topic Closed RSS Feed
13 Pages « < 8 9 10 11 12 > » Bottom

Outline · [ Standard ] · Linear+

 DFI nF3/4 series (LP and Infinity) users come in, Overclocking ability and troubleshooting

views
     
kianwee
post Jul 15 2005, 07:26 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(kelvin_hata @ Jul 15 2005, 04:46 PM)
hmm...if tccd need flash which 1??
*
You can use either one, but -1 works best for me (TCC5). -2 works best for my TCCD.
kianwee
post Jul 15 2005, 08:14 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(kelvin_hata @ Jul 15 2005, 08:05 PM)
i am newb in tccd...can i know wat the max fsb tat ur tccd can do it n wat vdim is good for tccd...

my corsair need 3.2v wen running 290*10 at 2.5-4-4-8
izzit to high for my vdim?
*
3.2V is a bit too high. I just need 2.8V to reach DDR600 on my OCZ Plat Rev.2 @ 2.5-4-3-7

Usually i use 2.8V + 0.3 enable
kianwee
post Jul 15 2005, 08:16 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(kelvin_hata @ Jul 15 2005, 08:15 PM)
hmm i oso dunno y this tccd need 3.2v ler... any ideal?
*
List down your Genie Bios settings for me please.
kianwee
post Jul 15 2005, 08:43 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(kelvin_hata @ Jul 15 2005, 08:29 PM)
fsb 300
ldt/fsb Auto
ldt/bus  16/16
cpu/fsb *10
pci 100mhz
cpu vid 1.450v
cpu vid special *123%
ldt  1.50v
chipset  1.80v
dram 3.20v cry.gif

n all the DRAM setting i put at auto onli set the 200/01 blush.gif
can u guide me setting the tci trrd...bla bla bla smile.gif
*
300
AUTO
16 16
10
100
disable
1.450v
1.300v
above VID * 123%
1.30v
1.70v
2.9V

200
enable
2.5
04
07 or 8
03
07 or 8
16
03
03
02
03
4708
auto
enabled
auto
0
level 7 - play with this (i'm best with 7, some good with 5 or 3)
level 1 - play with this as well (1 & 3 works for me)
8.0
6.0
256
disable
16
07
disable
kianwee
post Jul 15 2005, 09:18 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
That is a loose timing i gave you. You can try to improve by tightening it. See if this helps you.

http://www.xtremesystems.org/forums/showth...&highlight=tccd
kianwee
post Jul 16 2005, 12:06 AM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
Refer here:

http://www.techpowerup.com/articles/other/114

There are 3 types of bios every update.
kianwee
post Jul 16 2005, 12:36 AM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(kelvin_hata @ Jul 16 2005, 12:28 AM)
i still cant flash my bios wor...izzit i need extra boot disk?
but bios from DFI can direct boot, n techpower de cant wor...
anyone help...i am newb in flash bios sad.gif
*
You have to create a bootdisk, then unzip everything inside the disk

Then type:

awdflash BIOSFILE.BIN /py /sn /cd /cp /cc /LD /R /f

under A:\
kianwee
post Jul 16 2005, 01:02 AM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(kelvin_hata @ Jul 16 2005, 12:59 AM)
kianwee...i hav a good result wit 618-1 bios
finally my tccd can run at 2.9v... thumbup.gif  wit timing 2.5-3-3-8

superpi 1m manage 28.453 biggrin.gif
*
Well done man! Well done laugh.gif
kianwee
post Jul 16 2005, 02:35 AM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
nForce4 666 is out. (What's with the devil number?)


http://www.nvidia.com/object/nforce_nf4_wi...2_amd_6.66.html
kianwee
post Jul 16 2005, 11:46 AM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(state of abyssmal @ Jul 16 2005, 10:07 AM)
kianwee,
i think i gonna get the new ram.
mine can go futher anymore.. sad.gif
*
Yeah, get rid of the Hynix! laugh.gif

kianwee
post Jul 16 2005, 12:53 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(moderno @ Jul 16 2005, 12:18 PM)
ahahah...long live hynix!!....we can survive on DFI...yeah yeah.... tongue.gif

this hynix is all i got...uhuk uhuk...no money to grab tccd more...sad.gif
*
Join the TCCD darkside! ph34r.gif

user posted image
kianwee
post Jul 16 2005, 03:51 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
OCZ is back with TCCD.

http://www.ocztechnology.com/products/memo...m_elite_edition

600MHz DDR
CL 2.5-4-4-10

400MHz DDR (Dual Spec)
CL 2-2-2-5

kianwee
post Jul 16 2005, 06:35 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(ray99mond @ Jul 16 2005, 04:24 PM)
2T wor.......
not gurantee can run on 1T
*
http://www.xtremesystems.org/forums/attach...achmentid=34227

322 @ 1T, not bad.
kianwee
post Jul 17 2005, 01:23 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
I tried almost all settings and found out that lower LDT voltage gave me more stability. I tried 1.4 and 1.5 and can't pass SuperPI 32M no matter what configuration I use. I'm best with 1.3 and nothing more than that.
kianwee
post Jul 18 2005, 12:31 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(zangetsu- @ Jul 18 2005, 12:28 PM)
thanks for the product din...nanti aku g cari kat lowyat...
kalo takde ko buat la bulk  tongue.gif
*
Robyncom has it
kianwee
post Jul 18 2005, 04:59 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(ray99mond @ Jul 18 2005, 04:30 PM)
no one know ?  cry.gif
*
Refresh Period
kianwee
post Jul 18 2005, 11:00 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(ray99mond @ Jul 18 2005, 06:13 PM)
i mean how to calculate them like in a64 tweaker..
biggrin.gif
*
1552= 100mhz(?.?us)
2064= 133mhz(?.?us)
2592= 166mhz(?.?us)
3120= 200mhz(?.?us)
---------------------
3632= 100mhz(?.?us)
4128= 133mhz(?.?us)
4672= 166mhz(?.?us)
0064= 200mhz(?.?us)
---------------------
0776= 100mhz(?.?us)
1032= 133mhz(?.?us)
1296= 166mhz(?.?us)
1560= 200mhz(?.?us)
---------------------
1816= 100mhz(?.?us)
2064= 133mhz(?.?us)
2336= 166mhz(?.?us)
0032= 200mhz(?.?us)
---------------------
0388= 100mhz(15.6us)
0516= 133mhz(15.6us)
0648= 166mhz(15.6us)
0780= 200mhz(15.6us)
---------------------
0908= 100mhz(7.8us)
1032= 133mhz(7.8us)
1168= 166mhz(7.8us)
0016= 200mhz(7.8us)
---------------------
1536= 100mhz(3.9us)
2048= 133mhz(3.9us)
2560= 166mhz(3.9us)
3072= 200mhz(3.9us)
---------------------
3684= 100mhz(1.95us)
4196= 133mhz(1.95us)
4708= 166mhz(1.95us)
0128= 200mhz(1.95us)


Is this the one u looking for?
kianwee
post Jul 19 2005, 02:28 AM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(kelvin_hata @ Jul 18 2005, 11:49 PM)
i use tis
3120= 200mhz(?.?us)---> D@mn good for my ram biggrin.gif
kianwee..wanna ask u smth...wen ur ram run at 2.9v at 300fsb n test wit memtest86, izzit vyvy hot?
jus now i test my ram, i use my hand to feel the temp...WTF!!!D@mn hot arrghh...

anyone use tccd ram run at 2.9v? n can let me know wat ur tccd temp?
*
Yeah, it is supposed to be hot. laugh.gif

Don't worry, have heatspreader. I'm running at 2.85 now.
kianwee
post Jul 19 2005, 01:44 PM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(babyelf @ Jul 19 2005, 08:37 AM)
not everyone will run fine with 3120..

for TCCD 3072 works great and if i'm not mistaken kakaroto (g.skill rep) said to use 1.95us for benching
*
Exactly. 3072 works best for me.
kianwee
post Jul 20 2005, 03:40 AM

Cube
*******
Senior Member
6,562 posts

Joined: Jan 2003
QUOTE(leslie0880 @ Jul 20 2005, 01:53 AM)
anyone can help me?I m using the TCCD Ram (Corsair 3202V 4.1 2 X 256MB) now but confuse in the setting at bios??My MB is NF4-SLI DR!!
So ................"babyelf Master and kianwee Master"
Pls help me!!!
*
Any link for your RAM?

Loose timing:

200
enable
2.0
02
07
02
07
16
03
03
02
03
3072
auto
enabled
auto
0
level 7
level 1
7.0
auto
256
disable
16
07
disable
« Next Oldest · Overclockers United · Next Newest »
 

13 Pages « < 8 9 10 11 12 > » Top
Topic ClosedOptions
 

Change to:
| Lo-Fi Version
 0.0192sec    0.56    7 queries    GZIP Disabled
Time is now: 2nd December 2025 - 05:10 PM
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Removal Request
Powered by Invision Power Board © 2025  IPS, Inc.