no, its like in the pic i showed.. its used to cover the screw so it cant be seen

hey guys, i got one really newbie question..

my friend tried to cut his casing with a dremel tool, i was looking at him cutting the casing behind the window at the balcony, then out of nowhere the cutting disc just pop out from the dremel, luckily got the window to protect else might have fatal injury..

my question here is..how do u lock the cuttin disc tightly to the dremel?

disaster man.. luckily no one is hurt..

This post has been edited by kakicam: Mar 25 2011, 11:19 PM

yea..it hits the glass, bounce to the wall and just fall off below, thank god no 1 downstair..we went down to get the cutting disc before further injury is done but was broken into half

hoping sifu's will tell me how then we can make sure it wont happen again

don't stress the cutting disc too much. cutting using dremel should be done with lots of patience. look for bill owen's guide on using the dremel.

i have broken almost a dozen of those cutting disc for now. never had any injury. just make sure you we protective glasses when working with metal.

anyone know where i can get brushed aluminum with good price..? really need for my TJ07 mod... hehehe

how can we lock the cutting disc to the dremel? i mean what are the proper way? O_O

Lock ? U mean tight the cutting disc on Dremel ? I think the cutting disc that ur friend using is normal one . I have one suggestion which is better use Fiberglass Reinforced cutting disc because it didn't break so easy and can last longer

http://www.dremel.com/en-us/AttachmentsAnd...il.aspx?pid=426

If u have problem tight the cutting disc , u may try this :

http://www.dremel.com/en-us/AttachmentsAnd....aspx?pid=EZ545

yea..tighting the cutting disc on dremel..we are using the normal wan..then now using the fibreglass..wat i mean is..what is the proper way to insert the cutting disc to the dremel..cause the paper din write..n scared it's this problem

My suggestion is don't over tight the cutting disc because it may causes the cutting disc break

can meh..?

The cutting disc cannot last a hight pressure

i think better we tight it down properly to prevent any accident. in my knowledge, disc break not because of over tighten, but its the user press the dremel against the cutting object to hard. please be patient when cutting with dremel.

u got a point there...

any1 know people/ shop do cable management service area pj/ shah alam? just need my case neat, tidy and easy to access (change harddisk etc)..

---

Added on April 3, 2011, 2:24 pmops.. sorry.. wrng thread.. just move to http://forum.lowyat.net/topic/1202012/+760

This post has been edited by saster_182: Apr 3 2011, 02:25 PM

think moderno pc has it

Guyz...can recommend any shop / person who offer service to mod side panel like below? wanna match it with my cm 690 II also.. ><"



This post has been edited by nazseha: Apr 14 2011, 05:10 PM

i dont know if this is the right place for me to step in, but i want to ask 1 question..

i wat to clean my rig. any kind of suitable blower to blow the dust of? or just use vaccum?

sorry if im at wrong place..

For those who live in Shah Alam, Puchong, Klang, ya'all can get 100mm Bi Metal Hole Saw at CSM Hardware Taman Sri Muda for only RM65.00, 90mm at RM48.00, stock are available, 120mm u need to place order, 1week eta at RM80.00. Brands KUGEL.

Just nice for those who doesnt spend much on Dremel's, prolly already have hammer/drilling power tools. Just bought 50mm@RM19.00 hole saw to make 120mm blowhole look alike flower petal or KUIH BAKAR

Kugel's brand is from Germany.

This post has been edited by Shahirz: Apr 28 2011, 01:59 PM