Today start my midsem break so hv nothing to do

i wanna try to do sumthing with my HAF

My objective to paint my case to black color for interior n some red colour only..

Not involve any cutting2 coz i dun hv any cutting tool

1st off all i forgot take any photo of my haf complete ori set

NVM bout it

i buy [3 anti-rust primer][2 RED][1 WHITE][2 FLAT BLACK]



i use 800,1000,1500,2000 Grid sand paper for sanding process[cap burung2 terbang]



Take out all mesh on front panel



drill out all rivets



done "kekah"-ing my case



to post my update here i hv to build my rig on my table



tmr will start sanding part by part
sorry for bad quality pic.Using phone camera only

This post has been edited by doob: Feb 15 2010, 02:17 AM

thanks 4 d sapport

hahaha..yup
nothing to do then got idea to mod

juz some small part put red
the mobo tray n outer put flat black

i oso think wanna do tat
but dunno put wat logo
no idea

already bought red colour only
today n tmr sure shop still close
i only got extra white colour
still thinking wat to do with it

top put white??
i put flat black for top
i think wan put red
but i think not enuf red spray i bought =.=


coz they provide red led fan on d front
n i use red ccfl inside
i think red will make my case more "meriah"

That 100% rite

tuan asal dh kasi lampu ijau ni

thanks 4 d sappork bro

---

Added on February 15, 2010, 2:15 amupdate 4 today

done sanding part by part

[side panel]


[mobo tray]


dunno is it consider good or bad sanding job
my hand already feel very smooth rite now


then it taken outsite to do primer spray
very windy today..many habuk stick on it


PSSSSTTT PSSSTTTTT[spraying the primer ]


Biggest part done


Side panel + mobo tray


Done primer spray for today 3pm goin to eat coz starving


Final result on primer coat



This post has been edited by doob: Feb 15 2010, 02:15 AM

i got no cutting tool
only got drill
BTW how's ur project??
cant wait to see the final result

that steel a bit thick
if use hand hacksaw dunno how long it take
mayb my hand gonna ripped off 1st

This post has been edited by doob: Feb 15 2010, 01:37 PM

if use hacksaw how to start d 1st cutting??

already try
even d primer already hard to chipped off if using nail
use playar or other metal tool,then it will easy to peel

wow 200??
i use 800 1000 n 1500 only
tat 2000 i wan use for lapping my proc
today i juz spray 1st layer only
mayb evening i spray another layer
i dun buy clear coat
is it important??
it use for wat??

price?
same as normal spray??

i dun think can make that shiny
my house very windy
when spray got many small particle stick on it
FML

no use anymore coz that small particles already dry-ed with the paint

yup
i buy from hardware
very cheap 1

new update for today

done spraying my side panel[actually the colour a bit not fully red but when snap pic it look fully red..ull know when u see it with bare eyes]



spraying the mesh front panel[DONE!]



so sad..that part actually no need to rivet yet n my riveter slide on it

but done spraying 1 more layer on it



put it back using glue



the hardest part of all

its nearly imposible to put the clip back without tearing the paint



start rivet-ing



my hand so gatal already to put it back

luckily got no defect on it



my room become like this

kena scold by my father 99

run out of red spray
over use it on side panel

my place no got clear coat
hv to drive 40 minutes to get it
so sad

i got bed but i sleep on floor
already state there[the most difficult part]
hahaha
my nail feel like gonna peel off to put the clip back in
juz use my finger to take out n put it back
guna jari pon boley

This post has been edited by doob: Feb 16 2010, 04:47 PM

i use wanna make matte black
if put clear coat will make it shiny too??

thanks 4 d sapport
90% finised
juz a lil bit more work to finish my project