My 1st CM690 Mod...Codename 'Save Budget', 2 Years CM690 Need Touch Up!
|
|
 Jan 30 2010, 08:34 PM, updated 16y ago
Return to original view | Post
#1
|
 
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda 
|
Today i got free time to touch-up my 2 years old CM690...
 my objective to paint this CM690 to black color only....  ..not fancy color...just bored color...my 2 years old CM690 default condition  got oxidation at my HDD bay     my hardware lying on the floor after dismantled from CM690...so sad    work start...drilling to dismantle piece by piece...   This post has been edited by nidzamputra: Feb 1 2010, 10:15 AM |
|
|
|
|
|
Jan 30 2010, 09:23 PM
Return to original view | Post
#2
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
CM690 after disassemble process....
 used this one as primer/undercoat paint  then this one as my flat black  i'm used sand paper grit 800  right now in sanding process..will update later...  |
|
|
Jan 30 2010, 10:06 PM
Return to original view | Post
#3
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
so boring la sanding process..to much energy to used...huuhhhuhhuh
tomorrow will paint with primer...hope tonight i will finish sanding this case... |
|
|
Jan 30 2010, 10:47 PM
Return to original view | Post
#4
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
QUOTE(Jinster @ Jan 30 2010, 10:31 PM) oh wow, i have the same spray, and decker as u haha..never knew that decker can be used because it looks kinda slow to me due to using batteries >< yes..this BD it's ok if to drill out rivet..but if i'm wanna make a hole..i used cap ayam drill using power cord... |
|
|
Jan 31 2010, 12:00 AM
Return to original view | Post
#5
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
QUOTE(mfcm @ Jan 30 2010, 11:41 PM) cayalah..dh jadi modder pulak PSU xjadik kot murder mod sleeve...fan jer kene sleeve...PSU penat la... pasni psu plak jadi murder mod sleeve :-w |
|
|
Jan 31 2010, 01:01 AM
Return to original view | Post
#6
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
UPDATE...
sanding work already finished..this is result....i don't know this good or not result..if you see this...please comment...     now...i can rest then tomorrow i will start with painting job with primer paint... |
|
|
|
|
|
Jan 31 2010, 01:31 AM
Return to original view | Post
#7
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
cuti 3 ari bang..xtau nak watper...hahahahahaha
|
|
|
Jan 31 2010, 10:53 AM
Return to original view | Post
#8
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
meanwhile i need some extra job...need to clean up my intake fan...front intake and bottom...look so bad...and decided to manage one time to clean up all fan...look so dusty...
front bay intake fan    bottom fan intake    HSF need to clean up also...  This post has been edited by nidzamputra: Jan 31 2010, 02:36 PM |
|
|
Jan 31 2010, 02:36 PM
Return to original view | Post
#9
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
UPDATE...
painting process... paint my case with primer paint...i'm lucky today the weather so shiny...      |
|
|
Jan 31 2010, 02:56 PM
Return to original view | Post
#10
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
finished work for painting job..it's done...took 4 hours to completed this process...
      need to rest a few hour before proceed to assemble back process... This post has been edited by nidzamputra: Jan 31 2010, 04:39 PM |
|
|
Jan 31 2010, 05:37 PM
Return to original view | Post
#11
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
QUOTE(lhongwuh @ Jan 31 2010, 05:12 PM) i noticed some primer part not covered with black bro...missed that? yes bro...but finally i cover it with final touch up after riveting work finished...will uploading pic later...This post has been edited by nidzamputra: Jan 31 2010, 05:52 PM |
|
|
Jan 31 2010, 05:52 PM
Return to original view | Post
#12
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
now proceed to river work...
took 2 hours to finished this work...need to think first before seal the rivet...i do 2 or 3 mistake then need to drill out back rivet...   some primer part not covered by black paint     Added on January 31, 2010, 10:01 pmfinal touch up before assemble hardware to casing...     This post has been edited by nidzamputra: Jan 31 2010, 10:01 PM |
|
|
Feb 1 2010, 12:40 AM
Return to original view | Post
#13
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
finally almost 30 hours i've done my 'Save Budget'
 after cleaning all fan...    hardware inside my renovation room    modded CCFL at side panel...  |
|
|
|
|
|
Feb 1 2010, 12:40 AM
Return to original view | Post
#14
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
'Save Budget' in action
        |
|
|
Feb 1 2010, 10:09 AM
Return to original view | Post
#15
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
QUOTE(zuhaili87 @ Feb 1 2010, 05:16 AM) nice bro! may i know how much is the cost ? Flat Black Paint = RM5.50 *3 = RM16.50the spray ? the primer ? the sand paper, and other stuff ? im thinking of modding mine too if it's not too expensive. Primer Paint = RM5.50 *2 = RM11.00 Sand Paper 800 = RM1.50 *3 = RM4.50 Rivet Bullet = RM2.00 Total = RM34.00 for this job..i'm just used 1 piece sand paper only... |
|
|
Feb 1 2010, 10:11 AM
Return to original view | Post
#16
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
QUOTE(kimimaro_kun @ Feb 1 2010, 09:51 AM) WAA.... yes...this is fun time for me...3 days on leave make me rest & relax...sometimes it's can be release your tension...hahahahahahcongrats bro... mission accomplish already.. worth it took 3 days on leave to do modding Added on February 1, 2010, 10:13 am QUOTE(mfcm @ Feb 1 2010, 10:11 AM) haha guna 1 sheet sand paper pon sebab malas nk gosok ah tu  ...tau pun...lagi pon aku nak jimat...beli mahal tu sand paper tu...tauke kedai gred A punya sand paper...tp mmg berbaloi...tahan lama..tu pakai sekeping jer...satu casing leh gosok...This post has been edited by nidzamputra: Feb 1 2010, 10:13 AM |
|
|
Feb 1 2010, 01:03 PM
Return to original view | Post
#17
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
QUOTE(mr_maverix @ Feb 1 2010, 12:57 PM) nice prep job bro, and taking the whole casing apart before painting it..now i got some idea on where to start.. i just bought a new cm690 casing..gona spray it flat black inside before stacking in the goodies.. the idea put primer is good..it's work..the paint not so easy peel off...the important thing is you need sanding it 1st... |
|
|
Feb 1 2010, 02:48 PM
Return to original view | Post
#18
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
QUOTE(mr_maverix @ Feb 1 2010, 01:26 PM) the sanding can be done even without disassembling the casing part by part rite?? coz i dont have the riveting tool.. yes bro..it can be done even dismantling the casing...for riveting tool i saw last time it's cost only RM36...hehehehe..i think it's enough..no need mahal2 punya tool..hehehehe Added on February 1, 2010, 3:04 pm QUOTE(wutedo @ Feb 1 2010, 02:15 PM) welcome to the dark side.... tankiu bro..wakakaka This post has been edited by nidzamputra: Feb 1 2010, 03:04 PM |
|
|
Feb 1 2010, 03:31 PM
Return to original view | Post
#19
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
yes..using driller to drill out the rivet...
and used riveter tool to assemble back   Added on February 1, 2010, 3:32 pm QUOTE(wutedo @ Feb 1 2010, 03:20 PM) hg tak habaq kat aku pun nak wat.. kalau dak leh pi lepak ngan hang.. tulong mana2 hak patut aku tgk hang tak online pon..mcmner aku nak panggil..wakakakakaThis post has been edited by nidzamputra: Feb 1 2010, 03:32 PM |
|
|
Feb 1 2010, 03:44 PM
Return to original view | Post
#20
|
|
Senior Member
3,890 posts Joined: Feb 2007 From: Kuala Lumpur > Kuala Ketil > Kuala Muda
|
not so expensive for riveter tool...just RM40...
for the drilling size i'm not sure bro..let me check it 1st... UPDATED... i'm used drilling 3.0 size sorry for blur picture...  This post has been edited by nidzamputra: Feb 1 2010, 04:05 PM |
| Change to: |  0.0228sec
 1.06
 6 queries
 GZIP Disabled
Time is now: 9th December 2025 - 03:30 PM |
Quote