wut videocard r u planning to use? studyin from overseas watercooling setup most of them who went for cpu and gpu has 2 radiator, or a monsta radiator which is twice the thickness.

i suggest u rethink the hydra board, if u thinkin of pairing ati and nvidia u might as well scrap the hydra idea cause the latest demo they show and list the mixed card has 3 compatible games on it.....

my bad its more like 5 games lol ; ;
http://vr-zone.com/forums/510362/msi-big-b...ility-list.html

This post has been edited by kevink82: Dec 3 2009, 11:47 AM

i think it will be hard to make top bit a fill port if by "top bit" u mean the bit with the little screw on it as u have to tighten it to make it a close loop system?

u can take the whole top off to add liquid though

check if ur card is reference just strip the card and check the design on the block website.

This post has been edited by kevink82: Dec 4 2009, 10:43 AM

if u read it carefully it says tuniq tx3 win for load temp which is wut u want, no one cares bout idle temp pretty much ; ;

they dont deliver on sundays. they should call u if they happens to decide to charge u tax.

mild overclock should be fine but i dont think modernopc will take any responsibility if ur hardware fail though. should give them a call and ask first.

keke well thread starter says his stuff comin today, though no idea wut is ordered?

depends on ur setup for overclocking and wut programs u run, ur worklog stats 1x triple radiator.

usually ppl running i7 with overclock use dual or triple rad on their own since it runs hot, if u add ur gpu into it then ill say the temp wont be that good if any different to ur air setup?

u need to calculate how much heat it will put out and how fast ur radiator can remove those heat.

+1 for the pics plz...

keke yes u can ship it by urself and save a few or buy locally of course more expensive but u have the option of testing it out c if its working, and cosmestic scratch on parts u dont want before deciding to buy it or if it ends up faulty at least u have someone to blame rather than ship it back overseas and wait for replacement.

imo totally up to u i saw somewhere the xt block on sale for 59 usd, wut i really wonder is if i can ship a murdermod complete case here without and scratch lol..... maybe for next project ; ;

nice fan controller, but plz dont stick ur pump in the fan controller simply cause it does not have enough power to drive one unless u feel like blowing somethin up.

if u read any review on fan controller no one has made one that has enough power to drive a pump no matter wut it says on the box. someone tested the lamptron with delta fans and there were some problems. ur mcp655 has flow settings on it use that instead.

This post has been edited by kevink82: Dec 15 2009, 08:07 AM

i think it looks better than the kaze master, but a claimed of 30w per channel is pretty unrealistic to me by looking at the pic.

no heatsink at all ; ; it will probably melt if u really put 30w through the thing on 1 channel.

This post has been edited by kevink82: Dec 15 2009, 01:23 PM

take it to ur local alu workshop and ask them if u r too scare to do it urself.

they probably wont charge u too much anyways for a 10 minutes job.

i recon just stick with the lian li stock, there isnt many 140mm fans on the market and none of them stands out a lot.

u sure u need 6 fans on the rad alone? its gonna add lots of noise and push pull config isnt that great since u already have good fans on them doing push.

exhaust if u got another gentle typhoon go for it ill say, i remember claw has some new 140mm fans for sale so might wanna ask him.

some fans do make a annoying sound if u spin it down though.

yes ill say gentle typhoon has been recommended by many as the ultimate radiator fan.

its not so much it has wonderful performance but rather its more balance. wut u want is low pressure drop when the air goes through the radiator fins.

u wont notice much difference in temp so much maybe a 2-3c so i wont worry bout spending too much there. if u want ultimate cooling buy a marine aquarium chiller its like 1-2k ringgit and will chill water to 16c, i got one for my fish tank... if u dont mind the power bill its basically a aircon.....

lol yea no one is that crazy i dont think just a suggestion.

should read some reviews on xtremesystem forum

rad performance
http://www.xtremesystems.org/forums/showthread.php?p=4101259

fan performance
http://www.xtremesystems.org/forums/showthread.php?t=223391

it will turn out great man dont worry lol.

they asked tons of question because paypal is full of ppl that chargeback.... if u r them u will too since chargeback is so easy the customer just need to say its not wut i order and 50% chance it will get chargeback. also malaysia is in top 10 country for credit card fraud.......... such nice country we live in aint it .........

This post has been edited by kevink82: Dec 19 2009, 10:29 AM

i think they dremel cut ur panel though laser cut r clean and even on top middle and bottom where u cut it, ur pic shows uneven spots.

http://www.pcabusers.com/reviews/crazypc/scorpion/side.jpg <---- underwater laser cut panel.