comment on my settings....is dis temp ok??anything else i can do to lower d temp or its normal??

This post has been edited by phat_mcjack: Nov 21 2009, 01:04 PM

done..sorry for that...

i was wondering also....
i still struggling to get 4ghz

how to tell...mmm....i'm having sm problem to hit 4ghz...
dunno why...dis is d 1st time i'm using msi board..using gd65 by d way...
i can enter windows n everything...but 1/2core stop during prime...
dunno wats d problem...try 2 increase d vcore but no effect...

tried all u mentioned...lol...still dunno wats d problem...
u using same mobo as me rite?did u manage to get 4ghz??

i just crash my pc losing my windows...damn...
so hard meh wanna touch 4ghz???
i'm using d bios dat comes wit the mobo which is 1.2[how to flash in d 1st place..lol...]
i fed up wanna try to hit 4ghz..[wanna run without oc for few days]...
currently running 3.8ghz oni...but vcore 1.392....cant seems to stable lower than dis...never change anything else...all set to auto oni...turbo boost dsabled...

if any1 using dis mobo can get 4ghz using i5 750..pls do share sm tips...
i already tried even using vcore 1.462 ....can enter windows but could even pass d 1st 15 in prime95...

yes...

@bobiac

yes i did adjust d core ppl volt to


---------------------->my settings is as below:-->

mutliplier x20
blck 200
vcore 1.463
vtt 1.25
pch[1.8v] 1.9v
pch[1.05v] 1.081
ram 1.651v
c-states disabled
spectrum spread disabled
turbo boost disabled
eist disable
most cpu features are disabled except intel visualition teachinology[correct r?? forgot what is dis but d last in d cpu features]

---

Added on November 24, 2009, 12:00 pm@white lighter

you flash d bios got any improvement??
if yes in what aspect?

This post has been edited by phat_mcjack: Nov 24 2009, 12:00 PM

i'm getting like 63/60/60/60 smthng like dis...+- 2'c..using normal megahalem oni...but pull n push...
oh isit..i never thought of flashing d bios when i get d mobo...
thought of setting up d pc n oc..lol...
now u running wit wat setting??
would my ram multiplier/ratio n qpi effect d oc??
my ram multiplier is x4 n qpi is at x16..

i using normal ram oni...2gb kit oni 1333mhz...[well dats d cheapest i could get] its corsair....
and cm212+ is good also...best bang for buck...cheap but efficient...
wah ur vcore so low...i'm 3.8 also need 1.392v..
i wanna run x20 multiplier...coz i heard lynfields proc are good for even multiplier[correct me if i'm wrong i also just heard..dunno true or not]
so was planning 200X20 =4000...wit 1.42v...vtt 1.25...pch 1.9v..ram 1.65..
but xnot...
ur setting 3.9ghz stable?? you run prime how long??

---

Added on November 24, 2009, 1:21 pm@bobiac

ok boss...hey but how to run memtest in windows mode??? can oni run through bios isit?

This post has been edited by phat_mcjack: Nov 24 2009, 01:21 PM

oh ok...not sure abt my ram can oc to 1600mhz...
and i cant seems to run memtest coz i dont have bootable usb/floppy...
damn...any software dat make usb bootable??

lol..ok...
but atm i'll try to make my usb bootable thn run memtest...
later i tell wat happen....

ran the memtest[not memtest86]...dis 1 i run from windows...
ran about 3hrs+ found no errors...which gives conclusion that there is smthng wrong wit my settings,not my ram rite??

now i'm starting all again...lol...
cleared d cmos...
wanna see how much can go without any +vcore...1.251v is default for dis proc rite??

two app of memtest wit 896mb each...
run it around 3hrs+...
and wat u mean by full coverage?

i'm using 2x1gb...so run two memtest app wit 896mb each not enough??
how much then??

lol...wat 2 do all telling me to test ma...

@-pws-

i wanna oc my i5 750 to 4ghz+ but can seems t stable even at 4.9ghz..
can enter windows...but cant stable when prime...1/2 cores will stop...
if u read my previous replies u'll know what i meant...

@bobiac sudah la

now i already up till 1.9.. scare wanna up smmr...

@-pws-

i will update d template soon and post it here...

This post has been edited by phat_mcjack: Nov 26 2009, 04:41 PM

@white lighter

based on d ss...
i not so sure..as i'm not at home now...
i'll let tell wat i remember...

d load-line calibration = enabled
cpu voltage =1.463
pch 1.8V = 1.9
dram = 1.651
spread spectrum = disabled
other are auto..

---

Added on November 26, 2009, 4:49 pmas -pws- request...below is my setting...i can enter windows...but when prime my worker3 will stop working few second after start...

Active Processor [ALL]
Intel EIST [Auto]
C1E Support [Disabled]
Intel Turbo Boost [Disabled]
Adjust CPU Base Frequency (MHz) [200]
OC Stepping [Disable]
Adjust CPU Ratio [20]

--> DRAM Timing Mode [Manual]

CH1 1T/2T Memory Timing [1]
CH1 CAS Latency (CL) [8]
CH1 tRCD [8]
CH1 tRP [8]
CH1 tRAS [24]
CH1 tRFC [74]
CH1 tWR [10]
CH1 tWTR [5]
CH1 tRRD [4]
CH1 tRTP [5]
CH1 tFAW [10]

Memory Ratio [3]
QPI Ratio [16]

--> ClockGen Tuner
CPU Amplitude Control [800mV]
PCI Express Amplitude Control [800mV]

Adjust PCI-E Frequency (MHz) [100]
Auto Disable PCI Frequency [Disabled, Enabled]

CPU Voltage (V) [1.451]
CPU VTT (V) [1.250]
PCH 1.8 (V) [1.9]
DRAM Voltage (V) [1.651]
DDR_VREF_CA_A (V) [auto]
DDR_VREF_CA_B (V) [auto]
DDR_VREF_DA_A (V) [auto]
DDR_VREF_DA_B (V) [auto]
PCH 1.05 (V) [auto]

Spread Spectrum [Disabled]


hope you guys tell me wats my stupidity about...

This post has been edited by phat_mcjack: Nov 26 2009, 04:50 PM