I am using the msi P55 GD65 and an i5-750. I just have a small oc, 3.2GHz with turbo on at 1.188v (BIOS, CPUZ says 1.144v). I get 55C full load (25C delta T) with a c/m Hyper 212+.
Intel P55 H55 H57 LGA 1156 Core I3 I5 I7, OC and Discussion
|
|
 Apr 29 2010, 02:31 PM
Return to original view | Post
#1
|
 
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak  
|
|
Quote|
|
|
|
|
May 2 2010, 07:50 PM
Return to original view | Post
#2
|
|
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak
|
What is the recomended volatge for an i5-750 @ 3.2GHz (160x20) with turbo boost? Board is msi p55-gd65.
|
|
|
May 2 2010, 10:41 PM
Return to original view | Post
#3
|
|
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak
|
It should be okay if you dont have any crashes or bluescreen. Can you lower your voltage further? I am not really "pro" about the new clarkdales but i think you can lower your voltage a tad bit. Is speedfan accurate or what? You are getting 37C running prime? What is your cooler?
|
|
|
May 24 2010, 07:54 PM
Return to original view | Post
#4
|
|
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak
|
How low of a voltage could an i5-750 go at 3,2 Ghz with thrbo boost ON? not only the core but also PCH and another setting?
|
|
|
Aug 7 2010, 08:22 PM
Return to original view | Post
#5
|
|
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak
|
I would like to ask you all about ocing an i5 750. I am currently running it at 3.2Ghz with turbo on. I think I want to push further (and turn off turbo) but I can't prime95 it on 1.252v 180x20. I am using a P55-GD65 and running DDR3 1333 that is somewhat limiting me but I did run them at DDR3 1600 for a long time now.
|
|
|
Aug 9 2010, 08:58 PM
Return to original view | Post
#6
|
|
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak
|
Thx. i will try later.
|
|
|
|
|
|
Jan 14 2011, 03:07 PM
Return to original view | Post
#7
|
|
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak
|
I am curious because I am running 1.407v on my msi P55 GD65 with an i5-750 at 3.8Ghz (200x19) and a VTT of 1.361v. Is the setting allright for continuous use or i should raise the VTT and lower the vCore? The temps are quite low, around 75C with my Hyper 212+.
This post has been edited by RattleSnaKe: Jan 14 2011, 03:07 PM |
|
|
Jan 14 2011, 04:05 PM
Return to original view | Post
#8
|
|
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak
|
I mean what should i set? Maybe my VTT is a little low to be stable? Is your proc running at 3.8GHz?
This post has been edited by RattleSnaKe: Jan 14 2011, 04:06 PM |
|
|
Jan 14 2011, 05:26 PM
Return to original view | Post
#9
|
|
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak
|
Is my VTT too low? It is at 1.366v now.
Added on January 14, 2011, 5:46 pmActually the Vdroop of my board is very high. When i set it to 1.407v, it will drop to 1.344v when stress testing. It will crash easily if it get any lower. I alredy enabled the Loadline calibration. This post has been edited by RattleSnaKe: Jan 14 2011, 05:46 PM |
|
|
Jan 15 2011, 11:04 AM
Return to original view | Post
#10
|
|
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak
|
Actually what software you all use when stress testing?
|
|
|
Jan 15 2011, 11:41 AM
Return to original view | Post
#11
|
|
Junior Member
244 posts Joined: Apr 2010 From: Ipoh, Perak
|
The Vdroop happens in LinX more noticibaly. It only drops to 1.360v in p95. And is p95 stable enough? Or I need to pass the LinX test too?
|
| Change to: |  0.0200sec
 0.29
 7 queries
 GZIP Disabled
Time is now: 4th December 2025 - 09:02 PM |
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Powered by Invision Power Board © 2025 IPS, Inc.