AMD® Socket AM2&AM3 Overclocking V19, There's still few beasts hiding...
|
|
 Jul 24 2009, 10:41 PM
Return to original view | Post
#1
|
 
Senior Member
7,863 posts Joined: May 2007 From: highbury  
|
QUOTE(xixo_12 @ Jul 24 2009, 08:44 PM) [attachmentid=1098143] how the temperature when load?suicide push coz angry with boss at working place  no work for push high eventhough with additional voltage.. jet pejuang sound from the cooler..   |
|
|
|
|
|
Jul 25 2009, 01:19 AM
Return to original view | Post
#2
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
any software use to benchmark the cpu ?
|
|
|
Jul 26 2009, 12:57 AM
Return to original view | Post
#3
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
QUOTE(kuntawakaw @ Jul 25 2009, 08:00 PM) what is the actual speed?and this is a AMD thread.OC thread somemore..it is a forbidden to post intel SS here + no OC somemore yeah cq40 .. 3.0ghz on 1.05v » Click to show Spoiler - click again to hide... « i will go for laptop..i mean nettop..cheap small one.. msi wind perhaps..but luckily my money not allow me to.. huhuuh now i also play with laptop.. undervolting my frens cq-40.. so far there are 2 laptop to play with...will seek for lowest vcore for them..but the prob is i cant set the vcore permenently.. the stock is at 1.2v..k10stating and set at 1.05..stable but it will not last forever..it will reset back to 1.2 after reboot.  |
|
|
Jul 26 2009, 02:47 PM
Return to original view | Post
#4
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
QUOTE(kuntawakaw @ Jul 26 2009, 02:30 PM) no oc for lappy..but undervolt yes... cq 40 is too demm hot la.. i also cant make it permenent too . no idea how to do it . just turn on the laptop , then go open k10stat lor .everytime wan to play PES..i have to undervolt the vcore... i found the min stable vcore at my bro lappy.. prime for 15mins and pass... so i apply at my fren's lappy the same volt before do any intensive work (PES to be precise) and now i cant find the way to make it permenent..how a? (but my bro lappy is permenent to 1.05 iinm)  |
|
|
Jul 27 2009, 09:22 PM
Return to original view | Post
#5
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
gonna join you guys to oc next week. but my hardware is cheap cheap 1 lar ...x2 5200+ and asus m2n68-am .
|
|
|
Jul 29 2009, 01:33 AM
Return to original view | Post
#6
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
QUOTE(yvliew @ Jul 29 2009, 01:22 AM) cpuz?? play with your ram divider ?maybe your ram limit you to increase the fsb iinm |
|
|
|
|
|
Jul 29 2009, 02:33 AM
Return to original view | Post
#7
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
QUOTE(yvliew @ Jul 29 2009, 01:22 AM) cpuz?? change the memory divider ? your ram is running at nearly 900mhzThis post has been edited by fcuk90: Jul 29 2009, 02:33 AM |
|
|
Jul 29 2009, 03:01 AM
Return to original view | Post
#8
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
QUOTE(-pWs- @ Jul 29 2009, 02:59 AM) x4 B50 @ 4000Mhz (aka i7 4000Mhz w/ HT off) nice oc there bro .. wow the voltage still below 1.45v  [attachmentid=1106959] -pWs- |
|
|
Jul 29 2009, 04:54 PM
Return to original view | Post
#9
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
QUOTE(yvliew @ Jul 29 2009, 03:03 PM) 1 hour prime.. does this looks good?? any more suggestions? try go higher? |
|
|
Jul 30 2009, 01:55 AM
Return to original view | Post
#10
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
QUOTE(yvliew @ Jul 30 2009, 01:25 AM) 3.2ghz.. yay..... does it looks safe to use this speed?? this chips also not bad ya ....can go higher? |
|
|
Jul 31 2009, 12:11 AM
Return to original view | Post
#11
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
eh want to ask . my chip dropped juz now and a few pin bend , and i adjust it back , bt not 100% same straight . is it possible to power up ?
|
|
|
Jul 31 2009, 12:14 AM
Return to original view | Post
#12
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
dam bad luck . cod with a lynian just now . when check . haiz it drop . hope can power up lah .but now dont have the board .
|
|
|
Jul 31 2009, 12:20 AM
Return to original view | Post
#13
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
QUOTE(-pWs- @ Jul 31 2009, 12:18 AM) Processor drop? Should be fine provided pin not patah. no patah .lucky ==''' -pWs- straighted it back using small knife , hope can power up |
|
|
|
|
|
Jul 31 2009, 01:54 AM
Return to original view | Post
#14
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
QUOTE(antonio @ Jul 31 2009, 01:17 AM) use mechanical pencil....dun use anything that is huge in size... thx bro . straight ed .lucky.==''' if not wasted |
|
|
Jul 31 2009, 12:30 PM
Return to original view | Post
#15
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
biostar have ddr2 and ddr3 785g board combo
|
|
|
Aug 2 2009, 09:52 PM
Return to original view | Post
#16
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
erm .after i assemble all the part .the pc cant boot . or even post .means motherboard spoil? ram already use one stick oni .
|
|
|
Aug 2 2009, 10:01 PM
Return to original view | Post
#17
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
QUOTE(yvliew @ Aug 2 2009, 09:58 PM) what motherboard?? acer oem motherboard. when i get my new system.. i also encounter this....... so bad luck~ its motherboard .Added on August 2, 2009, 10:02 pm QUOTE(yvliew @ Aug 2 2009, 09:58 PM) what motherboard?? mine is not new system. i just want to clean the dust . i reattach the heatsink .then end up cannot power upwhen i get my new system.. i also encounter this....... so bad luck~ its motherboard This post has been edited by fcuk90: Aug 2 2009, 10:02 PM |
|
|
Aug 6 2009, 02:31 AM
Return to original view | Post
#18
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
normal load temperature for x2 5200+? i get 62c on load .using cm hyper tx
stock speed |
|
|
Aug 8 2009, 01:06 AM
Return to original view | Post
#19
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
eh .full load x2 5200+ @ stock with cm hyper tx
63c ?isnt it is too high ? |
|
|
Aug 8 2009, 03:41 AM
Return to original view | Post
#20
|
|
Senior Member
7,863 posts Joined: May 2007 From: highbury
|
@ah khoo thx .i will try reapply the tim .maybe i need to clean the previous layer of tim with the alcohol
|
|
Topic ClosedOptions
|
| Change to: |  0.0502sec
 0.29
 7 queries
 GZIP Disabled
Time is now: 29th November 2025 - 07:57 AM |
Quote