actually i did disabled it.. if not disable it, 1609 is where the DQS pop out... so i guess that is the main reason i cant get it stable..

the vcore enough edi..did tried it before i start with my rams..
and also now i test large FTT only.. mainly on ram (if use blend, 6mins pass then fail..if large, 1min failed- better i take large)

hmm..later find out

before i tweak the advance timing xixo + 8tvt tot, i can get stable at 1.60vdimm 800mhz..
after tweak the advance timing, i cant get it stable...
after loosen the altered timing, cant get stable...
after make the timing auto cant get stable.. all been done with 1.63vdimm

aiya!!!im going to kill myself..

let them rest for awhile...while im dead trying ti finish my assgnment

i adjusted the trfc..
and 2 other timing that i set at the lowest value (that is 7)

1st i make trfc 160ns.. failed..tried everything... failed..
then loosen.. 300ns... failed...


even revert back to auto will lead to same result..nahh.... my ram pening edi mebbe (bak kate xixo)
will take short break..and later will try figure it back...

xixo..
im not tested the cpu speed yesterday or any day before yesterday..
i tried today also..with the same setting of ram but using small FFT..

small FFT using all same setting passed fir 40mins.. but large will last few mins only...so wheather the IMC or RAM..nvm...i priming again.using diff divider (but i guess 1333 is the most favaurite divider for my ram)

now using 1600mhz divider..stock vdimm...
and trfc 160ns..all work fine.. 10mins prime and still counting

this is complicated.i stick with 1333 divider just now cuz 1333 can boot up to 18XXmhz but 1600 divider will boot only <1700mhz... hmmm.. nvm.

ram tweaking is the most complicated

bech copy score is far behind u.. adoi.

mobo or ram?

ram kingmax FTW!!! d9kpt..value ram
mobo 790gx...

muahiann

CPU 60 °C (136 °F) <-------- temp read by mobo
CPU #1 / Core #1 51 °C (122 °F) < ----------temp read by CPU itself
CPU #1 / Core #2 51 °C (122 °F) <---------------same..it 2nd core.from cpu


and u dare to put 1.4vcore with apache cooler? and that vcore is not needed for 3.6ghz..i can get 3.6ghz with vcore lower then 1.3 and 1.392vcore can get 3.8ghz edi... (what batch eh.might differ then)

i stick to higher reading that is the mobo probe one... safer
awal bagun sis...


able to stable setting...
hmm.. what else need to be tighten
i just notice i havnt tried tRc yet.. i just agak2 saja last time..not the tightest

This post has been edited by kuntawakaw: Sep 12 2009, 07:04 AM

sorry boss..cant fulfill that..
cl7 it will never more then ______ (argh...fogot the ram speed..but 283HTT x 1333divider)
but cl9 also will never boot at that speed..

once i try to boot with that setting, it will "cold boot"... 1600divider will stuck at 17XXmhz only..so that is the max speed i can ever boot with 1333divider

cl7 1800mhz stable is quite easy (prev few pages i did posted SS on it)
.. and beyond that i havent try the stable clock...

mine is 1x2gb module..kekekke.
single channel OC..

im a noobl eh.. i started OC late april..only 6months la..

i guess the TMPIN temp reading differ between board model.. ntah la..

saya merayu untuk berlainan..


(ignore the PCIE witdh..i have prob with that...not insert dupe card = x1. insert = x8 )

@superb88
u have to determine urself.. got few ppl using 720 here...u may ask cloudwan for his result..but ur result might differ then...

leave ur comp 6days per week? torrent? then i suggest u undervolt and underclock for a greener environment..dont foget to pull out ur GC as well.. -this is not related to ur question at all

the 4pin molex on the mobo or the 6pin on the GC itself?
i cant power up the PC if that 6pin connect not connect.
it will show some error... "even the GC bios at RBE will say so"
nahh... mebbe im too noob..

always handle with care..sure no prob occur.
but its better if not to often...mebbe..ntah la...

This post has been edited by kuntawakaw: Sep 13 2009, 08:10 AM

huge fluctuation there..

can post the idle setting..and leave to others to solve it..i ask for the SS only...

adakah itu 550BE unloc 3cores only?since the spec is stated b50 x4

---

Added on September 13, 2009, 6:30 pmi saw some voltage diff there...
same setting both of em?

u increase the cpu vid or cpu voltage?
nah...im not helping..ask ah_khoo or others..

This post has been edited by kuntawakaw: Sep 13 2009, 06:30 PM

owh..im late..never know propus is out edi
TS...u wan this baby badly right?
x4 at rm380...chun2
can unlock cache also... fuhh... if i have enough money..

630 also out
i wonder no BE for propus eh

xiukeong..
back from HK edi eh? long time havnt see u spam at gaming KB/mouse thread
u shud buy a PC then... go go... propus... propus

kekeke..
i sense some1 wan to buy... issat tru boss?
if cant unlock also dont care...cache only..and also 380 for a quad..that is demmm cheap..feeling like selling my b50 for this baby..huuuu....

@xiukeong...
AMD? owh no.... i hear intel from u

well.. i see 2 kind of responds for the unlocked "propus"

1: owh yeah..can be unlock..that is value then..i love it..AMD is generous
2: what?! AMD is good at rebranding.. i tot propus, but Deneb again.same OCbility

nah..i have the 1st kind of thinking..imma commoner.kekkeke

some +ve and -ve feedback from it...
which one u are at?

but to have such a cheap conform quad core is way too good edi... right TS?

i want this baby..i want this baby...
anyone saw 0927 sempron do tell me pls..this is the top prior now... GC later... PSU..later..HDD..later... next semester can buy them...this sempron,cant wait


This post has been edited by kuntawakaw: Sep 14 2009, 12:15 PM

ts..

ur might wrong then
the true propus out edi...
instead of cyc(Ape nth) batch, the propus batch seems difference..
not the cycX like deneb..

the OC of propus not so good but ok what for ppl not OC...
less heat ( i guess la)

@azilazwa..
mebbe..and yes perhaps
i have the same score of 3dmark 06 at same speed...
B50 vs 940 @ 3.6
so in real life i think same also...same architecture
(flame me if im wrong)