Because by looking at it, it seems the 'stuck' is usually associated with:

-Motherboard and CPU is having a 'communication error' thus making them both keep 'talking' to each other while forgetting to boot...
-USB related problem, try and cabut every USB connection possible and boot...
-Try minimizing boot, for example boot only with CPU,Mobo, 1 stick ram, 1 HDD and thats about it...
-Reset CMOS and then set date and ACC ONLY!!! reboot, if still blink2 like previously, try disable Legacy USB and set booting device to Boot HDD only (probably already been done )
-Use the template in my sig and post your configuration...

Erkk...but there is an X4 during POST right???

hmmmmm....

What bios are u using....Any known bios for unlock?

Set the ACC to -2% for All Cores

Drop NB an HT to 1800mhz

Manually bump CPU vcore at 1.4v and CPU/NB at 1.1v

try and have a look

Technically speaking, if you reboot from Bios and there is no boot or the computer still is in X3 mode, then it should be your chip is locked...but now, the problem is your chip can be unlock 'X4' but cant move after POST....hmmmmmm...

#mana kitab jalan Syaitan tak terbatas aku nie....

It could be a BIOS issue...juz hang-on until Giga release a new bios...

or

to confirm you 4th unlock cores can really work, try bringing you proc to your nearest friends that has a motherboard for unlocking....

There is the six pin..there are also the 8 pin type...



If you don't have 8 pin but need to use one, there is also an adapter...



This post has been edited by antonio: Sep 11 2009, 02:35 AM

Why not 790FX-GD70


First you have to know whether your ram is overclockable or not....If can go up to 100mhz without error and upping voltage then it is ok...but if raise up to 2.1v but gain only 50mhz, better don't...not worth it...

Whenever you raise your HTT, you raise your ram speed...

Ex. 200HTT / 200mhz

If raise 205HTT then ram becomes 220mhz....

easy...look at CPU-Z

in the memory tab look for your ram SPD...it should shows something like 4 diff acronyms which is basically the main 4 settings apart from the 1T/2T down below...

Look for the figure 5,5,5,18 and take note....take not of the acronym and their value...

Go into bios then set accordingly..

raise HTT untill PC can POST....the reduce back 3mhz each step until can enter windows...

where can think think wan...need description wooooo....

Owh...cooll....

Anyway, if I do OC comp, ok ahh....a lot of ppl use what board???

I afraid later title sponsor don't allow other brands of mobo....but GFX I can demand open....

I assume that most ppl (AMD) uses (according to rank);

1.Gaygaybite
2.DFI
3.BioBintang
4.MSI
5.ASUS

Or is it the other way round

Bio??? aiyakkk...that means Alpha tak pun Kaira (which is not official Disti)

Thinking of MSI or Giga actually....

Asus cannot lar....not cempion enough...

When I think of that, I think of TRUE

Probably Comp will run with DDR3....And most probably if do, will focus on CPU score rather than 3D....

Extreme category (or Open some would call it) should be fun, but I scared newbies, if seasoned OCer I dun really mind...

But extreme in terms of cooling lar, not overvoltage via soldering...


normal I suppose or maybe can squeeze the extra juice to early 20's or even lower...

Meaning if I want to go for WC, I will customized....

The only WC kit i will use is for HTPC....complete silence....

This post has been edited by antonio: Sep 11 2009, 08:12 PM

Like I said before, I dun think....I must either know the spec or read from somewhere else....

And most places that I read says that it is ok if you have bought one, but you probably look for an air cooling heatsink with silent but efficient fan which can do better...

Some of their air-cooling heatsink are in fact quite good when compared to the price tag that it carries...

But since CM wanna do like every segment of the market budget type of business, there are some that are totally north worth spending any pennies for...

My old CM Hyper 6 full copper now cools my HTPC fanless...I dismount the original Alu shroud and left the cooler just like that....playing movies with matroska format or watching DVD temp still ok...

And it is on a 2.6ghz Northwood, which lastime I put a fan on...wakakakakaka

aquagate ker aquagate S1???

Probably will do;

CPU-z
SPI
3DMark 2006

Of course will mandatory standardize the OS and the HDD...also the amount of software in the PC when OC.....

---

Added on September 12, 2009, 5:11 amI dun have 945 3.0Ghz but what I do have is Phenom II X4 3.5ghz.....

This post has been edited by antonio: Sep 12 2009, 05:11 AM

Basically there are two readings, one taken from the motherboard sensor which is measured through a sensor located below the CPU and one on the CPU itself...

Hence, the two types of reading you can see in program such as everest....

You otai maaaa.....not all chips can do like yours...

TMPIN 0 usually associates with the CPU and the TMPIN 1 would be the Northbridge (790gx chipsets)...Sometime there are also VRM sensors such as DFI boards....

1. Malas jawab...because a lot of fahaman...but to be short and simple...No
2. The slowest and lowest settings...which allows PC to boot easily....
3. Which means your ram now running at 1016mhz instead of 800mhz...overclock tuuuuuuuuuuuuuu

i know

btw I jalan 2.4v wif fan....active coool....

very not the hot...still ok...

Last time 3.8v BH-5...lagi gilaaaaaaa worrrrrrrrrrrr