few diffrent..i wonder how far u can go if 2.1vdimm

hehee.. bling2...
ur cheap fast dominator not enough?
now jus test how far 4-4-4 can go..and 5-5-5 can go..and i set myself 2.1v as a limit...

owh..ok..will try.but i did check twice..no MAL..
any other timing need to consider other than the X-X-X-XX-XX-XT and MAL? that quite important in oc?

i have a cm90cfm fan input blowing just 2inch from the ram...
and i still donno y.. 5-5-5-15-15 at 930mhz failed at 5mins.. using orthos 9 prior..
i wish it can reach 1k like the EPP#2 there..now post using my old home rig.. leave my pc at rest state a while

still CL5 also failed at 930mhz.. mebbe will stick the max CL4 850mhz...refresh mode select? i think it can be change la.. will try

means it stiff at the root.the very start of the cable..alah..lupekan..sukar untuk di explain..
its up to u...heheh..

cl5 can pass up to 880mhz..i think so...but not the max...still finding the max. so i found the max of CL4 (fogot edi..it shud have mention it on my prev post)
so now need to find the max CL5 freq with the same vdimm..now i frustrated d..

my bad my ram hates 667 divider so much...and a have some bad feeling with 533..the most suitable is 800 and 400 goes 2nd..
and i decided to use the 400divider since if i use 800,my core clock will be affected too much..

that ram timing...i guess its ok for a low speed ram like that..
mebbe will try cl3 after this if have enough luck

vantec ion je suda la...murah baget n lawa...
heheheh..once u wan to cf, swap along ur psu...huhuh

xixo..help me here..any other timings have to be tighten?

stress abit only..2night will stress kaw2.



Attached thumbnail(s)

i alter the MAL and refresh mode selct only at the memset..so reserve value for refresh mode select only set in memset...vdimm is ony 2.1.. ram speed only 580mhz...

too tight but too slow la sis..kehkeh..anything i can change? to tighten the timing..since it pass large stress for 10min..

detect wat? only use memset and cpuz to see the timing.. memset i only alter MAL and refresh mode select
said earlier.... 533 and 667 not suitable..my ram cant even run at <800 using this divider...
if use 800..my core clock will be 2.4ghz at most...so i using the 400mhz...

yup..slow by 1sec from my old KVR-AENEON ram config...
i cant play with multi... locked multi.
now using 10 instead of 10.5(max) because easier for me to calculate the ram speed...

this thread is dem silent..
wta
at 6pm... i oc my ram..not stable... so it wont boot up...after clear cmos..it can boot but will stuck at antivir load...
and done with the discharge..still it will stuck at the antivir load...
y?
now using safe mode to post..i dont think hw fault..most probably software fault..but y sofware effected by oc

---

Added on June 28, 2009, 8:09 pmproblem solved..done with system restore..but still i need explaination about it..anyone?

This post has been edited by kuntawakaw: Jun 28 2009, 08:09 PM

using bios.. the last alteration before cant boot is using bios..memset not in action today

oic... using 7..
i scared my 3days ram will go to rma...
last time before know what oc is, i will nvr use reset button..now, reset reset reset only..
btw how to disable the self generated report that need to be sent to microsft? the report that will pop out after nxt reboot of system crash

i dont care..if crash just a format and install new win..data all at other partiton..since i often do this.. per month around 2x format..

tracer so easy to rosak ya? nvr know that..luckily i nvr up the vdimm to 2.2v.. how fragile? relly high rma rate?
but i love tracer la...

orait.. i done with testing... so i know the ram limit d and i will run it at 580mhz only for now... HDD can kong if format many times ya? i heard that but i tot its like a "rumor" since my old HDD still working that been formated many times edi..
hmmmm
high rma rate ya? nvm... this ram, just blings.. later have enough money, buy cloudwan's ram..he said he can go for 1k...so i hope its better.

ya lo...esok pg die ade la...
ram? ini gamers maniac pye poison..huhuhu
aiya..just tried with 750mhz 2.0vdimm.. 4-3-4-18-24... passed..when change to 4-3-3, not stress yet da out..adoi.. i guess i better stop oc for 2day..

u must stay with ur kvr no matter what..huhuhuh..perfrmance ram is no no for ur board.wawaw

meh..come..i wan to buy also...the lowest price can be ever obtain

merajuk lah...

which M? 550+M770 c45+kvr 4gb..ok la kan? this M still available right? hehehe... .

btw if unlock the b50..need a 3dr party cooler or not? someone done with only stock cooler..whats the load temp? since theorically tthe tdp will increase as we unlock...

kehkeh...

bobiac..mind to tell hows ur cm tx3 perform? compare to stock hsf..if dont have the comparison with stock hsf...just tell me the load temp..thanks..

i think i want to sell off my gc la.. 2 weeks edi dont play games..i think i will go to dual monitor and bling2 pc.. and oc stuff..not into gaming anymore..

ya..come2.. want to buy for my donno-how-to-oc-but-wan-to-learn-oc fren,,,

kindda hard to evaluate from review..hehehe..since the ambient temp is diffrent

ya la...da 2bln..men game weekend je.. and this week + last week only 12mins play game...dem bosan altho have lots off incomplete games... haish.. 2 lcd more awesome.. 1 movie 1 ym or surf

assemble the ddr3 one..then when u see the tracer lying around doing nothing..u can post to me 1st..i dont mind.. jk jk

btw i manage to find 770 c45 from lingloong.. hehehe.. enough la for my fren

hehehe... mane taw hurry nk post tp xhurry nk pkai duet..wakawkaw

lemme pray for u bro cloudwan "jgn la ram tu rosak..jgn la..jgn la"

any news about the twkr edition proc? what i know is 140w and 3.2ghz..other donno..haish... and these also a rumor