it's like a cow facing it face to u and left side body toward u

kunta

i wonder where is located the robyncom? lolwut plaza?

owh see in front of lolwut plaza rite.. take the escalator? am i rite? i think mcm penah smpi before

ok2.. i think looks like rumah hantu edi.. no shop open, except that robyncom..

think to ask i7 there.. got cheap2 price or not
near to end of month

bryan, if staff/mod think one thread become spam thread, you guys have power, so just make it as forum post disabled, so nothing to shout out again about it. that is my opinion, post count doesn't show anything, but how well people mix on the community is more important.

so, just go on bryan to recommend to the board and disable the post count.

u are just realized it death?
i already feel it death long time ago after a few otai leave this thread.. i'm also will move on soon..
this thread doesn't serve well after a lot of newcomer come and enjoy this thread as spam area.. no intention to stop or make it as thread that full of challenge..

ya, u are correct about thing are not related to discuss here, but why?
only one i saw, i retired to hold this thread as TS because of this.. thread move so fast with non related stuff other than the result itself.

i already feel frustated more than you.. but if u want blame me because i'm said the not so correct statement, go ahead..

but you must stop first that spammer.. u know more than me right..

MAL set to 8ns
tRAS 11
tRC 15

layout for intel vs amd totally different eventhough same version.

This post has been edited by xixo_12: Jun 26 2009, 07:08 PM

what is the vdimm now?

1.95V

[attachmentid=1045287]

suppose MAL have in bios, it effect the stability of ram too.. if can't find, u need to tweak other way around.. play timing

about the failed.. CL leave at 4..

make it as 4-5-5-x-x

x-x tighten a little

This post has been edited by xixo_12: Jun 26 2009, 07:29 PM

yup that only need to care.. if u can't get using CL4, maybe u need to use CL5 also with back timing quite tight..
if ur mobo support refresh mode select to change.. then maybe u can use reserved value (15,6).. coz it faster

experience urself with the timing first.. each ram, will act differently.. but why CL5 test at 930, while cl4 850? what a weird.. give it test at same freq la..

go for high amp on 12v la

so if u think of future upgrade , do grab >700w

but i think Hx620 already melebih
400W 8tvt still going strong maa..

@ventri
lurking aroung here..

http://www.extreme.outervision.com/PSUEngine

i just put the value, but still cant exceed 600w overclock 4ghz cf summore

This post has been edited by xixo_12: Jun 27 2009, 07:38 PM

what is the ram freq and vdimm

remember, r u sure u can get that reserved value in ur bios?
too tight.. u gila la

This post has been edited by xixo_12: Jun 27 2009, 07:40 PM

u buy non modular.. mod it
it depend on u, modular on non modular, same only.. the different is skill and casing, how well u managed the wire

i prefer 620w wire

good u hv made ur choice...

u detect by what?

of course slow.. if only your ram freq is so strong, then u will notice it with tight timing..
better u aim at CL4 la bro.. with high freq..

---

Added on June 27, 2009, 8:00 pmi saw ur post at 7.32Pm.. pm me best price

it's up to u then

This post has been edited by xixo_12: Jun 27 2009, 08:00 PM