really? good..

dunno what wrong with my setting

Switch to:
Time Zone: UTC+08:00 China, Hong Kong....

I hope victek can modify the gui to have vlan configuration

I hope too, but i read linksysinfo.org and chances are little for that to hapen

hi,

i got problem with my tomato victek mode v1.25***. i notice since 4-5 day crazy, i used victek mod almost 1 month and everything work greet, but pass few day i notice i problem with my internet connection. after hard reset ( to default setting) and everything back to normal but then after use 12hour or ++ then internet connection disconnect. Even i try reboot it still same, but when i try hard reset everything work great again. Any one facing this problem before or just my line/modem got problem ?

thanks for advise guy. tq

This post has been edited by ramboo: Feb 8 2010, 12:49 PM

there's some "upgrade" going on with telekom lately. heard they wanna change our malaysia backbone to some super high speed stuffs.

arct, u mean it not my router or firmware problem ? other ppl got same problem ? my tomato victek on WRT54GL

cuz from what i see u said before this it was fine right? im using wrt54gl myself too with 1.25ND victek's tomato. recently i too get disconnected alot. and i see alot of ppl complaining about their screamyx too.

ohhh, thanks bro, clear now, i thought firmware problem, by the way, i set my router ip config to 192.168.1.1 and my modem to 192.168.1.2 , why i can access to my modem 192.168.1.2 modem and router link koz it different IP, if modem alone so no problem to access. any idea bro ?

you mean you can't access your modem at 192.168.1.2 right? the answer is simple. because you plug your Modem into your Router's WAN port. logically, they are on a different VLAN, hence you are not able to access your Modem.

ooo, then how can i acess to my modem if i link it with router ? any idea bro, i want check router and modem same time without unplug . tq RQ

Assuming if you set the modems IP to be 192.168.2.1 , go to Scripts ( http://192.168.1.1/admin-scripts.asp ) (assuming your router is 192.168.1.1)

In Init , copy and paste this (this is your client address , you can call it 192.168.2.x , its your call)



Then in Firewall Tab , copy and paste this , this is to allow connections to your modem so that you can add

bos i copy and paste everything but it not work for me, i check and test if access modem alone with 192.168.2.1 it work but when plug to router it cant work

This post has been edited by ramboo: Feb 8 2010, 06:18 PM

same problem

Did you put everything correctly , try sshing (get Putty) , and type the commands manually in Terminal and then that should do it

You might wanna turn off the firewall for a while (your routers firewall)

bos i try but still cant

maybe wrong somewhre, hope u can help, my router 192.168.1.1 and modem change to 192.168.2.1







This post has been edited by ramboo: Feb 9 2010, 09:36 PM

Your modem you change it to 192.168.2.1 , you gotta figure that out , SSH to 192.168.1.1 , to your router and login with root and as well with your admin password. Once you're in copy and paste those two commands I gave you and then try ping 192.168.2.1

You gotta make sure that your modem IP is 192.168.2.1

Hey Prasys,


ip addr add 192.168.2.3/24 dev vlan1 brd +
/usr/sbin/iptables -I POSTROUTING -t nat -o vlan1 -d 192.168.2.3/24 -j MASQUERADE

this part here, what is he suppose to put for the ip address? is he suppose to put 192.168.2.1/24 instead?

This post has been edited by red-queen: Feb 10 2010, 12:45 AM

bos even i try 192.168.2.1/24 or 192.168.2.3/24 still same no ping and no access from putty