haha, that's what i did too when i first bought this router. i almost wanted to sell it off but later changed my mind because of the support of third party firmware. after that i got a super cheap modem from the forums and now its working like it should.

Hi guys, a basic question

if i bought the router, do i have to flash tomato firmware first then only the Victek OR i can directly flash the Victek firmware directly that I get from http://victek.is-a-geek.com/tomato.html ??

Whoops, I meant to say that I plugged the cable from an ADSL modem into the WRT54GL. My bad there! Still trying to figure out if my settings are borked royally.

help please

try to set your adsl modem to bridged mode and see?


yep, you can straight away flash to victek's. but make sure u got the correct flash for your correct router. and ya!, remember to do the 30/30/30 reset to be safe.

30/30/30 hard reset

This post has been edited by arct: Jun 26 2009, 07:43 PM

but too bad victek firmware is abit outdated. the newest tomato should be 1.25

According to his posts on... I think the site was Linksys Info which is in Spanish, he is just making sure the firmware is up to par (Stable) as there was already a major error in the official 1.24 version of Tomato.

This post has been edited by vin123321: Jun 27 2009, 05:58 AM

hmmm im using tomato and so far so good. what's the difference between victeck and normal tomato? i heard it has better qos? well, so far im ok with tomato's qos and couldnt really reach peak bandwidth cuz now in my home there're only 3 ppl using. next week i'll go back to my hostel and there will be 7 ppl using. that time only i'll reconsider if i wanna flash to victeck or not.

victek's firmware can set amount of bandwidth for each client while ori tomato cannot. that's the main difference.

Hi all, back again with a new release after we fixed some inconsistencies in Tomato 1.24 & 1.25 official releases. So, here it's; Tomato RAF 1.25.8515 ND is released with the following changes and improvements over 1.23/1.24 and 1.25 official release.

Changelog:

_ DNSMasq 2.49
_ Busybox 1.14.2
_ Passive mode for Wireless Survey
_ Regulatory mode for wireless
_ Wireless Auto channel by default
_ TCP_Conntrack up to 8192 connection
_ Allow multiple MAC address per device
_ SSH remote forwarding allowed
_ More precise match for l7 ftp pattern
_ Miniupnpd updated to ver. 20090605
_ Wan_is_a_LAN feature included when WAN is disabled
_ All the features of Official Tomato 1.25
_ All the features of Tomato RAF
_ ND version with wireless driver 4.158.4.0
_ 140 IP/MAC in restriction table
_ 140 IP/MAC limit in IP/MAC limiter

You can download as always from http://victek.is-a-geek.com/tomato.html

In test version section you have the link. Also the source code following the terms of the GPL is available in Source code section.

Enjoy!!! and also comment any issue you will find.

thanks !!!

hope can resolve disconnect issue , when heavy p2p .

wow... great. will try it out later~~

wow!! i've been waiting for this for long time. thanks victek!!

Thanks again victek - cheers !

will wait for the non test version from victek. now running stable with 1.23 8025

barry80, go for this test version, after 1390 downloads no issues has been reported. Almost of complaints was due to inexperience from user. I'll fix as stable version today.

Victek

I am wondering in OpenWRT , its possible for people to have more then 1 AP (i.e 1 AP for Guest and 1 AP for normal users). I just want to ask if its possible for you to do that !

P.S - Victek , Tu eliges

This post has been edited by prasys: Jul 6 2009, 09:51 PM

for normal usage..it's perfect for me...no issues. same as 1.23 version. thanks alot again to victek.

1.25 ND version seems to have better wireless quality compared to 1.23 ND...

I've just upgraded it. It works very well and I'll post a picture of my heatsink most. Applied a bit more of thermal paste and pasted a heatsink so that the router would run even cooler under heavy load !