how to bend acrylic, HOW?LIghter?heat gun?
     |
|
|
 May 3 2006, 05:41 PM
Show posts by this member only |This post's rating (0+, 0-) | Post
#41
|
 Do You Feel LuCKY PunK ?  Group: Senior Member Posts: 1,517 Ratings earned: 0+, 0- Ratings given: 0+, 0- Joined: Jan 2006 From: Between Those Legs Position : Missionary    |
erm...
i was thinking of bending or cutting an acrylic the whole day today while driving.... i was thinking of making a shroud for my new Radiator... but needed to do some calculation to get those stuff... Plexiglass , Cutter and Glue.... or can just take the measurements and go to a plexi shop and ask them to make me one... hehe...  |
   |
 
|
|
|
May 4 2006, 02:44 AM
Show posts by this member only |This post's rating (0+, 0-) | Post
#42
|
 Xtreme Modding Group: Senior Member Posts: 991 Ratings earned: 0+, 0- Ratings given: 0+, 0- Joined: Jan 2003 From: PeNaNg  |
QUOTE(ikan_semilang @ May 2 2006, 01:11 PM) Bring it on..  Bombman said around below RM10 for that knife..   QUOTE(nelza_ax @ May 2 2006, 02:09 PM) bombman.. ya lar..mebe shud bring it on.. ill be the 1st to get it frOm you  Can just get @ most hardware shops ppl but dont get somthin' too cheap lah. As I said earlier, get the SELLERY brand. The blade vry long-lasting nelza_ax : If u want, I can get for u. Easier 2 COD  |
|
|
|
|
|
May 4 2006, 07:04 PM
Show posts by this member only |This post's rating (0+, 0-) | Post
#43
|
 i am me Group: Senior Member Posts: 864 Ratings earned: 0+, 0- Ratings given: 0+, 0- Joined: Sep 2005 From: PeNaNg  |
QUOTE(bombman @ May 4 2006, 02:44 AM) Can just get @ most hardware shops ppl but dont get somthin' too cheap lah. As I said earlier, get the SELLERY brand. The blade vry long-lasting nelza_ax : If u want, I can get for u. Easier 2 COD ok jugak bro..around rm10 rite? btu nnt2 la..very2 busy rite now  |
|
|
|
|
|
May 4 2006, 11:46 PM
Show posts by this member only |This post's rating (0+, 0-) | Post
#44
|
 Getting Started Group: Junior Member Posts: 275 Ratings earned: 0+, 0- Ratings given: 0+, 0- Joined: Apr 2006 |
sigh....tired...just finishing diying my cpu casing....still got bit more to do..
if u wall want to bend the acrylic...plan a date the meet up somewhere..then i'll bring the acrylic bender... |
|
|
|
|
|
May 5 2006, 12:48 AM
Show posts by this member only |This post's rating (0+, 0-) | Post
#45
|
 หมัด เท้า เข่า ศอก Group: Senior Member Posts: 3,622 Ratings earned: 0+, 0- Ratings given: 0+, 0- Joined: Jan 2003 |
QUOTE(nelza_ax @ May 2 2006, 12:59 PM) @bombman..mana nak carik natang tuh kat sini? Go any hardware shop and ask for plastic cutter QUOTE(ikan_semilang @ May 2 2006, 01:11 PM) Bring it on.. Bombman said around below RM10 for that knife.. A good one that signboard making shops use for minimal cutting cost around RM20-RM25 |
|
|
|
|
|
May 7 2006, 02:57 AM
Show posts by this member only |This post's rating (0+, 0-) | Post
#46
|
|
Xtreme Modding Group: Senior Member Posts: 991 Ratings earned: 0+, 0- Ratings given: 0+, 0- Joined: Jan 2003 From: PeNaNg |
QUOTE(nelza_ax @ May 4 2006, 07:04 PM) ok jugak bro..around rm10 rite? btu nnt2 la..very2 busy rite now Haha...xde hal nye QUOTE(Acey @ May 5 2006, 12:48 AM) Go any hardware shop and ask for plastic cutter A good one that signboard making shops use for minimal cutting cost around RM20-RM25 No need spend so much also. The one I'm usin' already vry reliable. Used so long for all my mod But sometimes slightly more xpensive due to bundled blades  |
|
|
|
 |
| Lo-Fi Version | Time is now: 20th March 2010 - 05:49 PM |
All Rights Reserved 2003-2009 Vijandren Ramadass (~living on a prayer~)
Powered by Invision Power Board(Trial) © 2010 IPS, Inc.