can anyone tell me where i can buy the peltier module (thermoelectric module) in malaysia? Is it d only way to order pelt via internet ?

I need it urgently.. thx much guys..

Best to enquire with the 2 water cooling bulkers in LYN which arev metalzone and dinster

thx.. hope can buy frm there..

Hmm... i'm short of Voltage.... pls help me to make a psu run at least 15V. can any Guru's help me? W/O any load, i reached 2.9c n it's on 11V ( my pelt rated at 15.4v @10A 89W).

pm shah81 to mod a spare psu for the 15V supply... just out of curiousity... What u cooling wif a 89watter pelt?

Yup, thanks bro Amok. Already sent him PM's. Hmmm.... i'm just testing the pelt, running full 15.4v vs 12v, how much drop in temp i get. Just doing another DIY project.

anyone knows where i can get dielectric grease in KL?
thanks

I've got a large tube that i got from HUM...

Ehh, you know the one that is used with the machine for bringing the heart to beat again when there is no heart beat?

Ala, the maching that gave an electric shock straight on a person's chest?
That machine have to be used with the dielectric grease you know...

I've got one large tube [The tube is as large as the largest tube of Colgate paste]

Hehehe...

i love ur modding. it is too innovative and creative... if i got this brain, i'll make $$$ out of it.. haha.. ^^ lovely nice..

you can try PM a forumer ff7yta.

i bought my pelt from him but never used the pelt since..

maybe i'll start my mod later..

edit: or u can directly go to his thread here.

This post has been edited by coolmast3r: Dec 19 2006, 12:57 AM

Dielectric grease, easier to get small tubes from mechanics.

It's the tune-up grease they use to connect the 'octopus' to the sparkplugs.

I found a tube at ACE hardware. Used it for my sparkplugs like it's meant to be used . Not doing any extreme cooling yet.

did someone here know where i can get this n how much is da price,coz i saw forumer in here post his rig using this freezone cpu cooler but i cant find hin to ask where da hell he get that cooler,this cooler is cool dude here some attch........................

ermmm this is da web www.coolitsystems.com

Attached thumbnail(s)

anybody can teach me to pelt my wc kit? i want to cool off the water inside my wc kit.. 2 me its a lot safer .. no need to look for condensation.. i thinkk...

seriously not worth the effort TBH with you. Sifu amok did that before. PM him for the results and if you still wanna try, tips and tricks in doing that

as we can seee.. if u ever heard of coolit freezone.. they do it dat way.. by pelt the coolant... and if im not mistaken.. it uses 3 peltier module...

where can i buy lapped copper block.. like master amok uses?

This post has been edited by cookietiau: May 10 2007, 01:24 AM

What's all this ruckus about CoolIT Freezone?
Is it that good or just romours?

ermm.. well i found it from some oversea magazine like maximumpc.. the review really good and i think we can duplicate it by do it in version.. hehe..

it uses TEC module to cool the water.. to me its a lot safer by doing that because the is no worry about condensation...

but at least we can give a try...

or why dont u go the their website?

This post has been edited by cookietiau: May 10 2007, 02:43 PM

apparently its good when theres not that much heat output. can go below ambient...
but when u've got a lot of heat or when load, it's a different story. the peltiers cant keep up and u end up with temps higher than a good WC.
we might be testing one out though, so we'll see.

Bro's,

For proc's based on the 775 sockets, is it still necessary to fit on a cold/hot plate between the proc/peltier/waterblock or can we just slot the peltier in between the proc and waterblock?

I've also seen a couple of ways to install the peltier but mostly on socket 478 procs, for 775 sockets, is it still necessary to fill the proc socket with dielectric grease?

of course lerw.. otherwise condensation maaaa... huhu.. correct me if im wrong..