tapirus
i'm waiting u to get one of the HR-05 IFX to update me
next TT i belanja u makan

my bios setting, voltage for CPU add = +75mV (1.34V )



my rig

oledi tried my DKP35 today after got it from jy14 this evening

been struggle to boot it up in the 1st place as no display come out on my monitor....oh $hit...not like my previous NF4 lanparty again

tried with different gcard..then it's finally boot turn out my outdated 7300GT spoiled oledi...huhuhu...

thanks cstkl1 for assisting me on the phone scared the mobo spoiled as i'm replacing the NB heatsink with MCW30..(that's how my NF4 lanparty died)

tomorrow will boot the system up fully when my HDD arrive

prelimenary temp in the bios show 29c for e2140 on stocks speed / (Apogee GT) / NB Chipset 36c (MCW30)

eh guys...did u take off the white square rubber pad beneath the stock NB heatsink and reused it again beneath the new NB heatsink? i tried to peel it off but torn out in few places...then decide to leave it

then better leave the white rubber pad even u change to new hs.
it works better and safer that way

yeah...better leave it there coz when u tighted up the water block, u tend to tight the screw as much as possible...so, the Rubber Man might save the day...

I tried HR05 IFX/SLI on this DK, performance almost same as U6, both without using fan.

the rubber pad sticks on bottom of the stocks NB...not left on the chipset there....i tried to peel it off to put it back bu to no avail broke it to few pieces..

at the bottom of the stock NB heatsink, rite?...noticed that one...and since the HR05 came with the rubber pad, never bother with that one...but yes, really important to have it there...

just wanted to share some Genie BIOS page... the BIOS date is 24/12/07
the setting is @400x8 with tweaked here and there though...

current system setup


Genie BIOS Setting


CPU Feature


DRAM Timing


Clock Setting Fine Delay


Read Delay Phase Adjust


Voltage Setting


PC Health Status


POST

you guys no g00d,told me that TRUE cant install vertically on the DK.
but look at mine!!!!

anyway,i hate this mobo anyway,using only 4 layers PCB,the bios cannot undervolt the processor vcore,and sometime cannot boot up,stuck at the Dark logo screen there,have to reset and only can POST
have some vdrop on quaddie,will try to prime and see the exact vdrop tonight.

and one thing,how u guys update bios?

this is the HR-05 SLI/IFX on the DS3,
abt same with u all mobo coz the location of it abt the same...
but have to bend a bit coz might touch the gc,

dun wana bend also can, have to put and isulation rubber or btw them...

i did put a sponge btw them,
but at last decide to bend a bit

i didn't tell anything...
so... why some TRUE user said that can't install vertically...?

@sniper


actually....
it's magic for mine to be installed so nice.

, apa black magic you use aaa?
anyway... what's the issue installing this TRUE le? ? the heatpipe hiting the NB sink? the fins?

A little out of topic here... anyone experiencing problem with the ICH9R controller or the SATA cable?

At the moment, my rig is having this major problem: http://forum.lowyat.net/topic/634995

So in the end, I ditched out the new Seagate 500GB HDD from my rig suspecting it's a faulty HDD. Windows installation with the old Samsung 120GB HDD is alright, till at just now I'm experiencing BSOD and in the latter mentioning something such as... Beginning physical dump. It mentioned if this is the first time I'm experiencing this problem, try restart... if problem persist... check new hardware installation... etc. etc. (I guess most of you know the content well )

I tried to restart the system and it happen that the loading taking a long time at BIOS and latter disk error . I thought my ram having the problem and thus going into BIOS again to set the RAM to 5-5-5-18 @ 1.8V. In my horror, the BIOS couldn't detect my HDD when I checked at the setting . I tried to restart and it remain hang at the DFI DK logo screen . In the end, I switched to another SATA cable at another SATA port, voila ~ the system successfully booted into Windows .

Any comment on my severe problem? I couldn't afford system down any longer or my assignment will be screwed

hmm, last time i faced similiar problem with u,
at last is the graphic card problem and mobo,
last time mistaken got a modded gc,
and the soldering not good,
sometimes touch and sometimes dun...

and it make the mobo went crazy,
then i change new mobo,
and resolder back the gc,
it went good....

Now even the graphic card could lead to my problem. Anyway, replied to your post in my thread. Hope we can continue there .

guys...may i know why the CPU-Z shown the wrong multiplier ek? i set it at 8 x 400 as shown at BIOS startup...but cpu z shown 6 x 400...waduh...

You didn't disable the C1E and EIST in the BIOS option . Read kmarc's overclocking guide and you'll get it .

ahaha..super noob here when OC'ing an Intel

which part in the bios to disable this C1E & EIST?

here dude...

ahaha..done oledi...

managed to get good temps on the NB with MCW30...but the CPU reading when up kaw kaw from 29c idle to 60 only at VID 1.4v...aiyak....dunno if it's accurate reading or not from the smart guardian...

damn... 410MHz? nice clock dude... what about other settings can share, me wanted too to get 410MHz FSB

dunno loh bro...just test it only at 5 minutes...ehehe...all settings are pretty much as the same as urs...just my cpu temp there puzzling me a bit as i'm on WC...should be lower than that...hurmmm...

owh now at 50-52c...pulak dah..ahahaha...

which 1 is vcore..

- cpu vid special
- cpu vtt voltage

EDIT : Moderno u got my pm right???

cpu vcore is vid special

uiks ur water block not properly contact ka bro

@AceCombat

try disable the logo screen and see which part got problem when it is hang. maybe it is the oc fail, and you either need to press F1 or Del to continue.

well,the NB heat sink and the upper PWM heat sink did blocked the heat pipe of TRUE
today i upload a pic again and u guys know how i install.


i got this problme too,when I RAID 0 my raptor,it hang at the POST screen there,CTRL+ALT+DEL and make it restart but it keep on stuck at the Dark logo screen.
Clear CMOS and set back all the setting will make it POST successfully


nope,not oc fail,luckily i managed to press Tab button and look at the POST,it hangs when it detecting HDD and DRAM
i guess is Intel RAID 0 problem,know why?cause it uses only ICH9R and when i raid 0 my raptor,there is 4 port left,i use 2 port to put my DVD-RW,so i think there is the problem.
when i use my Asus,i always put those DVD-RW into JMicron controller in order to prevent some conflict.
right now i running raid 0 in my raptor and both of my DVDRW also in ICH9R,but i change the port and everything seems ok
Raptor in SATA 0 and SATA 1 while DVDRW in SATA 4 and SATA 5.



This mobo only 4 layer PCB.....

yeaah the upper hsf will black..not jus 120xtreme..mine tuniq oso block with it n NB hsf..but the NB hsf jus crash with fan not hsf..so wont b proc coz i make abit spacer for the fan..but the upper hsf crash with hsf fin..so no more choise ..plug it out..replace wit ramsink waaa ace regret getting this mobo yeah?coz its oni 4pcb layers?

so ace...change mobo la...previously i was about to take the Mars; then came the DK - switched to DK;not really sure whether it was a right move or not...till now.

ya lo,a bit regret,i dont like its 4 layer and one thing the most important to me,cannot undervolt the vcore


before i got this mobo,i was thinking to get Mars,looks like i made the wrong move,mars should be better
oh ya,no matter how,i'll use back my Asus mobo when it comes back

Just sell it lor..... cheap cheap sure people buy ma....

Now that I'm using my new 2nd-hand DFI Blood Iron, I feel that my previous RMAed Ga-P35-DS3 is better, in many ways such as:
1) All solid caps
2) Good boot options/settings
3) Able to use USB BIOS flash
4) Not as cramped as the DFI
5) Able to undervolt
6) Cheaper

I compare this two as they seemed like the same low-end budget "performance" mobo.....

guess, the better board from DFI is UT version...

anyway... frankly speaking, i do have like vearn27 and AceCombat XP-ed... it hanged sometimes @DRAM/HDD testing... , don't know why though... but it happens sometimes...

u mean,OS make it like this?

hmmm...i think there is possibility that someone (or a few of them) will change their mobo...and who knows that i might be the first...
*** eyeing other mobo with my super vision rite now... ***

got my new setup here with E2140

(huhu sorry my blurry hp pic...will take more pics with my digicam later)

running E2140 @ 1.39v (415*8 : 3320Mhz)

but got problems on the cpu temp...it went up from idle 29-31c --> 58-60c during prime...


will change the fans to a higher cfm fans later today to see if any changes on the cpu temps

hey mister moderno, where'd you get the processor? 415MHz now...

ahahaha...it's from Mr. Clawhammer

eh..u're using the HR01-Plus right? how's ur cpu temp at 400*8 / 1.44v?

owh... patutla... from Clawhammer, if from SeaMonster... i'll be damned

nope, HR-01 , the temp @65°C max with AS5 applied while idle ±37°C (lowest i can get)

clean ure rad dude.
not suppose to have such high delta.

suspect gunk or trap air.

oledi cleaned it before switching on the this mobo...

the NB temp are quite normal for WC temp...max out at 42c during load...but cpu temp is puzzling me...shoot up to 58c ~ 60 from 30c idle...

will try to switch those low cfm 120mm silverstone's fans on the radiator with evercool 120x38mm 70cfm later today

there was a arguement on this on a few forums
this is what was said basically

from G0, MO, C0 stepping basically all those that came after B3

intel designed the DTS to be inaccurate below 60C.
so basically all the idle is wrong which i think is true.
heck u should see mine..
1.48v load is 68C
1.5v load is 80C.. go figure wei.

for quadcore is another story la, if you try c2d then you'll found that this mobo is much more better than DS3. for c2q, sure go for UT/LT

yes,C2D works very well on this mobo,but quad make me

but unfortunately, it is very hard to get the UT/LT in malaysia

haha same goes with our dk bro..hard to get in msia..but can get from SG the nearest...haizzzz itschy hand to buy new e8xxx like this..haizzz seem can wait more longer w/o oc my rig now

that's the reason why i change my Q6600 Go to E8400 ..

haha, very good idle/load temp and freaking vcore of 1.1v only. really feels good about that.
and the vid for my new E8400 was 1.0xxV , i just love it, but sadly, dk can't undervolt, or else.........

that's what i meant...even the DK is hard to get; not to mention the UT/LT...SG also selling like hot cakes...no stock maaa


i also thinking of getting the E8400 from general_odin, but he was late about 20 minutes and the stock got kebas by other buyer...so, no more stock till now...mmm, oc'albert, where did u get ur E8400?

Hmmm..... yeah, I've read that quads really cause bad vdroop on lower-end mobos..... UT/LT.... err...... too high-end for me la.... me not rich guy....

I actually wanted to get the DK P35-T2RS but couldn't wait for bulk..... too long...