Warning : DO NOT post anything other than pictures/configurations of YOUR watercooling setup, screenies, etc. Please keep this thread clean and neat. To discuss about watercooling and results, click here. Thanks.

Overclockers United is getting a little stale so lets just spice things up shall we? Lets just post pictures of our watercooling setup along with screenies!



I'll start with my setup, a 24/7 folding@home AMD system.

AMD AthlonXP 1800+ DLT3C NIUHB 0334WPMW @ 2.54GHz @ 1.85v
Kingston HyperX PC3200 @ 242FSB 1:1 Dual Channel 2-2-2-11-1T @ 3.25vdimm
DFI NFII Ultra Infinity w/ Oskar Wu's 04/1/21 bios, 1.8vdd
Antec TruePower 480W

DangerDen RBX Lucite Top, 1/2" Fittings
Double Heatercore, 1/2" Fittings
Evercool 120mm fans x 4, Push n' Pull Config.
Nirox P3800 Pump
bulkhy's Custom Made Cylindrical Acrylic Reservoir
aleck's "Super Oil Tubings"
Distilled water. No additional coolant, yet.

First off is the Heatercore,


and comes the reservoir,


along with pics of the crudely sealed Nirox pump,


and of course, a shot of the entire wc system. Pretty simple loop w/o the GPU block.


The acrylic reservoir's shining glow is an effect of a Sunbeam's UV LaserLED passing through them. Quite pretty, but the heatercore's still without any fan shrouds No pics of the RBX block as it's available all over the net.

Finally, here's a temperature screenie of the system running full-load folding@home (project 859) for >4 hours.


At an ambient temperature of 32c±, the watercooling setup records an average load of 44c±, an increase of 12c± above ambient, with a 80w± processor, comes an amazing 0.15c/w± efficiency. Pretty "cool" I'd say. But of course, they are nothing more than guesstimates as I do not know the actual cpu temperatures and the wattages produced on the waterblock itself. IIRC 2.2GHz @ default 1.5v does 35c idle and 37c/38c± full load. Will post up screenies of them later.

In the meantime, do post up pictures / screenshots / config of your own watercooling setup as well.

Edited : Changed the image storage provider. UploadIt.org expires
Again, please post your questions & thoughts about watercooling here. Thanks.

i'm using Thermaltake Aquarius 2 kit.

Pics will come later..

Idle temps 39 - 41 degs depending on room temp

Load temps 48 - 50 degs.

Room temp range from 28 to 31 degs. No Air Con.

specs are as in my signature below

- D-Tek White Water CPU Block
- Hydor L20 Pump
- Innovatek Fass-O-Matic Reservoir
- Black Ice Extreme Radiator
- CoolingWorks Shroud
- Enermax 120mm Fan
- ClearFlex tubings

XP1700+ @ 2.3GHz, 1.68v
35c load, never idle







.. will update the link in my siggy later

My first WC setup: (courtesy of bulkhy):
block ~ DDM3
pump ~ nirox P2800 (leaking all over so i used epoxy to fix it)
rad ~ custom made by bulkhy
res ~ custom made by bulkhy (very nice acrylic)
tubing ~ bought from hardware shop. RM0.60 a feet. aleck please send me better one.

Comment: ~ The temp slightly better than SP94/Tornado and I can sleep better now with the pc running 24/7. This WC setup meant for my next Mobile Barton setup. But with this result, I think I shud have one more set.

Here's my screenies after 25 hours 2 instances of prime at 3.5GHz. I am shooting for 3.6GHz stable.

My econo Water Cooled Rig :

Denger Dan Maze 4
Nirox 2800
Ace Hardware Tubing 3/8 ID
Bulkhy's Reservoir
Alu Radiator from potong kereta. 120mm x160mm
Sanyo Denki 120x120mm Dan 2600 rpm 80+ cfm
Diy Rad shroud, cut from tupperware.
9:1 Distilled Water/Prestone Automotive Coolant

Epox 8RDA3G + Amd Barton 2500 @2.2Ghz fsb 200x11
Corsair TwinX PC3200 2x256mb
Thermaltake Butterfly 480w PSU
Icute Casing

Folding 24/7

Temp : Full load 42C @ ambient 32C

My humble Aquarius II
Specs are in sig.

AMD 2400+ XP-Mobile Barton FQQ4C 0402 MPM (avg quality/stepping)

2400+ @ 2.588GHz (246 x 10.5) @ 2.0vcore (actual 1.95v)
Kingston HyperX PC3200 @ 246FSB 1:1 Dual Channel 2-2-2-11-1T @ 3.25vdimm
DFI NFII Ultra Infinity w/ Oskar Wu's 04/1/21 bios, 1.9vdd
Antec TruePower 480W

DangerDen RBX Lucite Top, 1/2" Fittings
Double Heatercore, 1/2" Fittings
Evercool 120mm fans x 4, Push n' Pull Config.
Nirox P3800 Pump
bulkhy's Custom Made Cylindrical Acrylic Reservoir
aleck's "Super Oil Tubings"
Distilled water. No additional coolant.

Repositioned the heatercore to a better spot, added a little extra cooling aiming at the casing/motherboard and PCI exhaust blower to combat the heat generated from my new 9800SE-256bit, and voila! Mobile/Barton DOES run cooler than a Throughbred

43c on load, 36c idle @ 32c ambient.
Sandra2004 reports 158W @ 2.0vcore.

This is my 2nd water cooling rig I just built for my son.

Danger Den Maze 4 Waterblock
Nirox P2800 Pump
Bulkhy's Radiator
DIY Reservoir
Aleck's Tube

The system configuration

AXP 2000+ running at stock speed and voltage
Abit NF7 v2
2 x 128Mbyte PC2100 DDR
1 x 256Mbyte PC2100 DDR
Maxtor 40Gbyte 7200rpm
Ati Rage Ultra 16Mbyte
Sony DVD Rom
AeroPower+ 350W PSU
Chieftec DG-01BD-U Office Series Case Black

This is not an overclocking rig just for a normal usage as I got my old DDM4 block.

Naked glorry:

AMD Athlon XP 2400+ Mobile Barton
ABIT NF7 Rev2.0
256MB X 2 Twinmos module w/ BH-5
ATi RADEON 9800SE -> PRO (To be cooled soon)
Enlight 420W

WC Configuration:
Aleck's jet impingement water block
DDM Chipset/GPU Block
Custom made condensor with 4 X 12cm 89CFM fans
2 X Nirox P2800 Pump
Bulkhy's arcrylic reservoir

Here is my 1st watercooling system since August 2003

Cascade Waterblock
Eheim 1048 Pump
Custom Made Radiator 3 passes, 3 rows with 120mm fan and shroud
DIY Reservoir
Eheim Tube



Idle Temperature

Eheim 1048
Danger Den Maze 3
Black Ice Radiator

AMD Thunderbird 1.2 GHz
256 MB Kingmax TinyBGA PC133
IWill KK266 (Survived a water spill and didnt let me to upgrade to a NF7, long live IWill though)
128 MB Gainward GeForce4 Ti4200 (Minor drop of water on the card while running, shut down then wipe it off and run it again, still alive and kicking)

My watercooling setup

Setup:
Dangerden Maze 3
Black Ice Micro (built around 80mm fan)
Eheim 1048 pump
Bulkhy's custome made reservoir
Tygon tubing, Blue UV dye, water wetter

my temporary watercooling setup

1/4" tubing system
pump + reservoir - estimated rating at 150 liter per hour
radiator - 4 pass 4 rows + cooled by NMB fan at full speed
waterblock - i think using spiral design, but donno what material for the block.

performance = slk700 + smartfan2
but still cool when water meets electric rite??

the whole setup

a close shot to the watercooling kit

introducing...
waterblock - radiator - pump+reservoir

idle, XP1700 at default.
CPU FAN = RPM for the rotor of the pump

2nd WC Rig:
Thermaltake Aquarius II + GPU Block(not installed yet)

Specs: tbred 1700 b @ 1.833Mhz
DDR400 Dual Channel D43 RAM
Abit Geforce Ti4200
Albatron Km18G Matx Nf2 Mobo
Maxtor Diamondmax Plus 9 200GB
Seasonic Active PFC 200W
NEC 2510 DVD Burner(haven installed)

mbm5 screenie below

Here is mine......
Overall view...


The crazy huge double heatcore...


Close up on the DangerDen RBX block...


The pump and custom res...


Top view....

my "official" watercooling setup after the "temporary" one
perhaps the first "watercooled pc" in UIA

very very space saving


the whole system


oopss .. casing not yet finish modified...

Here is my rig setup.
1800+ AMD XP Unlock.
8RGA+ Rev 0.6
512x2 OCZ 3700 EL PC3700 Rev1.0
Antec TruePower 480Watt

The water-cooling setup. Sorry didn't manage to capture the res/pump picture

The waterblock, with moded barb.

Bulkhy's homemade radiator with 2x120mm fan with push-pull effect cooling.

The res/pump, with moded barb as well.

There you go, my really humble rig now... eheheh. Hope you guys enjoy it

Cheap casing. homemade PSU wire sleeving ,side panel also DIY radiator bracket also homemade . Truely poorman's mod. Old calender, it's 2002.

Side view of rig with my PC with my homemade water cooler

The homemade reservior

Da pump...

My homemade water block... tested with high pressure tyre pump and test it on fire using camping gas, of course with water running. mount it on P4 bracket by using costom made stainless steel clips not screws.

Back view of my rig

This is my watercooling setup:

W/block: Jet Impingement Water block by aleck
Rad: Bulkhy's custom made
Res: Car brake fluid container
Tubing: Alech's tygon tube
Pump: Nirox P2800
Fan: 2x120mm NMB fan

So here u go.. the water block..

the radiator..

the reservoir.. brake fluid container..

the pump showing off...

close up on the w/block..

overall look..

System:

- Lian Li PC6070A - Abit AI7
- P4 3.0C @ 3.54Ghz - 236fsb 1.6V
- 2x512MB Mushkin PC3200 Black Special 222


Temp:

Idle - no idle
Load - 49C

Btw, im not really satisfied wif my temp tho. Its kinda high. Im xpecting my temp to be lower than dis, below than 45C. Do Abit mobos really report high temp than it is? My temp b4 water cooled is around 62-64C w/out sidepanel n 68-70C wif sidepanel. IM still happy wif the setup. Managed to hit 236fsb at the moment, was at 226fsb. Mayb hav to get better radiator n pump? Any suggestion do pm me. Ok thanks.

New setup:
Danger den Maze 4 (AMD)
Black ICE Xtreme 2 Radiator (2x120mm)
Danger Den Single (5 1/4) Bay Reservoir
Eheim 1048 pump
Aleck's Tygon Tubing 1/2"
(Water wetter, blue UV dye, distilled water)


A close up on the Rad.. (Xrossfire's handywork)

titan water cooler kit

review

more

Some preliminary shots of my new water system, screenshots and shot of complete loop to come later.

Project PaloCool....updated

1800+ Palomino AX1800DMT3C AGOIA022MPM @ 1.725 ghz
768MB DDR RAM @ 150 mhz
Shin-Etsu X-23 Thermal Paste
Chieftec Full Tower Dragon Case

Loop: Pump-Rad-Waterblock-Reservoir

Dangerden TDX
Dangerden Double Heatercore with shroud + Dual 120mm NMB fans (sucking)
Nirox P2800
Bulkhy's Reservoir
Distilled water



Ambient: 34c
Idle: 37c
Load: 44c

Quite satisfied with the result and everything fits into the big case!

PS: Gotta love the ghetto tubing!

Hie there, newbie here and hope to learn more here..anyway here's my bong (evaporative) setup. I know it won't work that efficient in hot and humid weather here in malaysia but still giving it a try as i'm quite out of budget for a heatercore/radiator for the time being. Anyway here's the spec and pictures:

CPU: AMD Barton 2500+
Clock Speed: 2.3gig (200X11.5)
RAM: 256 X 2 hynix d43 module
Waterblock: DangerDen RBX
Voltage : 2V
Temp (idle) CPU: 45 Case:33
Temp (load) CPU: 52 Case:35

Still looking for highest possible overclock and haven't relli mess with the ram yet.

side view

fan blowing cold air into the bong

the waterblock

waterblock mounted on my nf7 during testing

Mine at last....

Using...
aleck's Jet impingement waterblock
aleck's wonder tubings
Nirox p2800
DIY reservoir (Bulkhy's clone)
Bulkhy's Radiator
Nidec Beta V

Using 2.25Ghz @ 1.7V
10x225Mhz with d43(dual channel)

Proc
Ambient 36c Load 42c

System
Ambient 33c Load 35c