did u try increase the VCore?it restart maybe bcoz of not enough power supplied to the proc.

does unregular voltage on Vcore affecting the cpu....cuz i noticed the power sumtimes can goo down to 1.43.....although rated is 1.525.. normal also get 1.48 only

adjust vcore not damage ur cpu la if not above 1.7volt. try increase ono by one step la.bcoz all ur hardware good already except ur psu la.u try up vcore 1st.

tried v core 1.6 last time....upped the core till 220...
not stable though...lastly i need to reset cmos jumpers...ahahaha
i think ill think about it back after i get a new psu...must be a really limiting factor:)

i hope so..but if change psu still cannot oc high2?

mybe hit the wall oledi

i hope not....

later buy psu then tell us u oc k.so wat brand psu u want buy?wattage?

to whacker:
hey how is my cpu? can oc higher?

wahh...u can oc to 4.0gz still can boot ?me 3.8ghz onli can boot.after that kena reset cmos

well....real power maybe nice....or thinking of a low budget not that expensive psu...not going to oc that high...any recomendations??

erkk..dun know much about psu la.but i buy acbel 350w true power :rm 130 still ok with 6600gt , 3x hdd , 2 x optical drive ...... cheap and powerful.


OMG..my 2.4ghz (northwood) proc heat is 47C when just on my pc and 60c when 10minute..is that normal? 47C with 3700RPM cpu fan is too high i think.and if i turn down RPM to 2600 the heat be 61C.going to change to WC i think.

ya.. on asus p4c800
but i sold it to whacker

huhuhuh..nice item...
nway...from ure guys experience...
which s478 with which proc is the best oc'er?

@ zt_lee,
what is u cpu temp?u use wat cooler?




i think 2.6ghz HT & 2.8c ghz kot.

D1 stepping 2.6c good?

From:


To:


Is this good on stock cooling ?

u cant do this on stock vcore?

btw..its too little..i mean d speed

erm..2.4c??

it can be on stock vcore and stock cooling.no need to up vcore bcoz speed not much different.BTW, u kuala terengganu where?push more la .make 3.0ghz

i'm doing 2.4 to 3.0 (sumtimes 3.3) on stock hsf...
still ok maaa..

wow..ur cpu fan power la.me oc 2.4 to 3.0 on CM fan still 60c.

nope..juz using the stock..full load oso 63~64
+ ac5..

ya la.i mean ur stock fan la power. 64c still ok?later u cpu burn

no lar..using dis few month oledi..nothing happen..
hehe..now using the hyper6..but wrong installation (dunno how to install ) temp 68

better u fix it fast.later burn rugi la.hehe..anyway hyper6 cam with manual izzit?

YA LAR..CUM WIF MANUAL..I'VE FOLLOW THE MANUAL OLEDI..BUT NOTHING DIFFERENT ..I'VE TRY ALMOST 10 TIME BUT STILL THE SAME..MAYBE NOT NGAM WIF MY MOBO ...

maybe it wan u install water cooling kot

my 2.4 northwood ;




so hot 1 i think

aiyaaa..same wif my presscott lor..

very hot for northwood..phew..better change your cooling system..use high end air cooling or water cooling..hehe ..by the way you very lucky using northwood...my prescott reaching its limit only till 3.4...beyond that cannot boot..

Not really remember the 2.4c@3.6ghz what temp liao...but i m running it at water cooling.

Now at prescot 3.0GHZ E0 stepping , highest get 4ghz..

wahh..nice proc + nice stepping...
xkan 4.0 je kot

Here's mine as of my sig:

kucingfight..what psu are u using??
69c same like mine

tat was the previous Vtech 350w on Asus P4P800. Now back to AI7 and Enermax 431W

3.3v ~~ 3.14
5v ~~ 4.97
12v~~11.13

wargghh..

whats the 12V rails for actually...was wondering why people stress out that particular voltage

12v for the hardware..

as in the motherboard plus gc,proc and all?

my max push....



pls give some comment...

ure doing it on stock or wut?

juz asking..izzit ok we just testing using super pi?? not using the prime>>

i run my system with CM jet 4 with full speed... actually a temp is 65C that time..so hot for northwood core right?yes i wan to change to watercooling 1 by end of this month.no got 3 pc to care..like wife need money onli

update :

just oc to 3.1ghz and prime 7 minute temp u know how high?70C already. my 3.2ghz lga onli 58C ~61c max.

too hot for a northwood.. me using prescott oso 68c oni

maybe if use good thermal compound can up for 60C maybe.but better i change to WC la..now got same money to spend.

Update!! but no priming yet



huhuhuh

haha..good 1.. now i found another problem . when start up , my tempereture ( in bios) said it 55C but in windows said 42C.when i priming that day in windows said it 65C so my bios ? 78C? OMG . . so which one correct? FYI , this pc use MSI neo2-v (MSI 6677 maybe) .

try updating the bios...got the same temp reading problem at first before updating my bios....using neo2-ps