hmm some how my with my ds3 bored i fail my orthos test at 8 minute plus oc to 3.28ghz any one got pass orthos with longer time?izzit my value ram?

my rig oso kenot passed orthos atleast 8hrs whenever my e66 speed over 3.2Ghz
no matter wat setting(vcore/ vdimm/ chipset voltage(s))..

can any1 help both of us here??

I'm using E6300, manage to pass orthos for about 5 and a half hours @ 457x7 (3.2ghz) @ priority 9 with the following settings

Vcore: 1.35v
vdimm: 2.1 (using Kingston Value Ram @ 5-5-5-15 LoL )
vmch: +0.1
vfsb: +0.2 (or maybe +0.1)

Load temperature was 69c (aircond off)

so can Intel G965WH board oc a D 805??
Sorry for the nood Q. Newbie here.

im a newbie here...asking can a willamette 1.8ghz be ovreclock to the maximum? im so scared it might explode.. i overclocked it to 2 ghz

cpuz:

Can u guys enlighten where is the option to set the pci frequency to 33mhz in DS3? i cant seem to find it.

ds3 dont have pci frequency. just set the pci-e frequency to auto or 100 then ok d

okay. Thanks.

come on man i need help....ok for me overclocking has reach up to 3.4g n im happy with it on my e6600...but i just bought the winfast 7950gx2 and since i plug in this card i cant even overclock my proc no more why huh...so now runnin in standard non oc spec....not even a slight overclock will cause the pc to restart...but i heard else where that ds3 board support this 7950 gx2...help plz...

Had u try diff bios? like F6, F7, F8i and latest F8??

im on f7...now about to download f8...wat f8i anyway?beta or modified?

F8i is beta which seem good to me...F8 is official bios, but many said is not that good for extreme OC...

Well...when I enable the Auto Voltage control...My Temp 70c,when I select manual.My temp became 65c......E6300 2.9GHZ.Wonder what's the use of the voltage control in the F7 bios ?

when u set Auto Voltage, the mobo will automatically adjust the voltage needed by the proc for its clock speed. So it auto increasing vcore and temp too. buthen if u set it manually the vcore wont increase.

i think i am not explaining well, anyone can help?

Well....If OC to 2.9GHZ can set manual ?

still having no luck...cant get new bios yet seem like the internet international site is down...guess i ran my pc on standard setting now...

2GB is still ok ,but i think that the Willi can't overclock very high speed.Mostly around 2.1 or 2.2GHz would be the max speed as it's generating a lot of heat.

Ahh, probably thats the problem. using F8i, i manage to run my e6300 2.8ghz @ 1.185v, passed overnite orthos. But once i changed to F8, the lowest vcore i can boot into is 1.206v (cant remember the exact decimel!)

Anyway, can you point me to where you've read about the quirks concerning the F8 bios? thanks

One more question, what do you do when you get looping restarts? its kinda annoying and i still cant find a way on how to make the cmos reset (other than doing the whole jumper thinggy offcourse). It will reset like randomly after 5 restarts or so.

I once OC my Northwood 3.0GH @ 3.15G with Gigabyte 848P chipset. now change to Abit IS7-E 865PE i cannot get 3.15G to run stable. both ram and timing stay default like previous mobo. what went wrong?

Your statement is a bit blur,put a screenie of CPU-Z,then we can help you.To change the RAM timing,you have to do it in bios mode.

F9 is out. Get it Here

Seems to be a lot better than any of the F8s.
Read about it here.

Darn.. im still at the office. Wish i was at home to try this out

Anyone tried it out yet? Do report.

F9 seem very good to me... I am doing 480X7 at the moment...OCCT tested stable...I think still got room to improve...

darrnnn! thats one hell of a good oc. I still cant get pass 460 fsb which can only work in f8i.

before f9, what was ure highest oc?

dammit, ive just playing with official F8 bios, now F9 already release!! wth?
less than 10 days again release new bios. they dont have better works 2 be done ka??

btw, here my short test with F8, b4 this i cant stable when clock speed more than 3.2Ghz

I can go as high as 3.5GHz...but need around 1.55vcore....Now I only need 1.5v for that....
Now I running 425X8 @ 1.512V....

haiz..sob sob..even with tis F9 my e6300 oso kenot go more than 2.8Ghz..heard that week 28 is good for OC..but mine didn't work out i help my fren OC his rig which is week 24..his proc (e6300 too) juz simply can hit 3.2Ghz on air reli sob lor...

erm.. how come kenot reach 3.0gig?. what ram u r using?? maybe your ram bottleneck your system..

as you will need 429fsb x 7 to get 3.0 gig, then if u are using value ddr2-533 ram, the ram might be unable to reach 429fsb.. the situations happen to many of my fren here

list down yr dram timing/setting for both system. we will try to help

ur new m0obo is better than gigabyte..
hav you chech ur vcore? vdim? naaa..3.0 ---> 3.15, should be piece of cake..

hi there all forumers..i a noob in dis OC thingy..i juz tried to OC my e6600 with my intel stock HSF..the temp shown in the CoreTemp is damn high..is dis 4 real? or myb this is normal when using stock hsf..FYI, i've triend refix d hsf 4 several times..

ere i oso put some screenshots. hop dat all d experts out there can help me out ere.. thanx in advance



here's the screenshot of my e6300 OCing test..hop d experts can comment on dis too

hahhahaha...i guess i can say goodbye to my gigabyte board now...somehow the bloody board failed on me couldnt reboot...there goes my ds3...very lazy too manually flash the bloody bios...


all i did wrong is tryinng to update using @bios but didnt realize its a revision 2 bios...i thought my board is revision 2...haih...turn out to be its revision 1...

somemore when i try to boot it it just restart over n over again till my 7950gx2 burn....suddenly the 7950 gx2 chip just burn!!!damn...

can see the light n smell oso..goin to rma it my 7950...but the ds3...i just totally lost hope affraid to use that bored again,so just now go buy the asus p5b board...and now runni on it...but i think my ds3 still can be use...if you have the tool to manually flash the bios though...and got guts to try it on your system...but for me,so damn affraid edi wanna use that board....even though there is no mark of burnin on the ds3 watsoever...
well goodbye gigabyte and hello asus...

frank_fusion..

yup.. high temp is normal when u r using stock hsf... it is always good idea to get reputable third party hsf..

here's some reference - credit to soulfly...

thx 4 d link bro..after read dat,i know i shd consider any one of dis 3rd party cooler..but d temp,isnt it too hot? if its true,i can boil water n have maggi instead..hehehe

hehe..definitely x bcoz of ram..coz i'm using corsair xms2 667c4...i think tat ram should b easily reach 900 if oc...

y not trying pumping higher vcore..masak the proc a while...perhaps can clocks higher?

Hehe...so happy,just got my DQ6 with E6600....i'm using 2x256MB Micron D9,and i'm new to OC stuff....can anyone tell me what speed can i reach?
Thanks....

ya....masak aka burn in the proc....but watch the temp...dun over masak...


2X256mb? is kind of low for today usage..
6600...hmmm...with proper cooling and solid power supplied...I think easy can get to 3.5GHz and beyond....

Can anyone suggest a good HSF to use for OC on Abit AI7 mobo?
Proc : 3.4G northwood

sure easy but to get the stable setting kinda hard leh

yup.2x256 might be a low supply for nowadays...but my money already habis liao lo....so bo lui to buy better one,just wanna know lo...now still finding HSF to suit on it....a bit headache,dont know which to get,need sifu help here....

i oso looking for new HSF to coolen up my proc..stock hs seem too hot for me..btw the best way to look for 3rd party hsf is in the cooling n hard modding section..

omg thats so bad. remember that REV.2 boards (u can see at the PCB) comes with dual X16 PCI-E slots.

CAREFUL Alert for DS3 USERS!

To t3chn0m4nc3r

ur using the same ram as mine. but running at 895?

whats ur ram timings, divider and voltage?

-deleted by myself-

ANyways, something about the new bios for DS3, F9
Anandtech

Seems like its one hell of an overclocker. Wish i had one of those lovely rams

I OC my DQ6 with E6600 ES,i put multiplier 9x with 300FSB,suppose to be only 2.7GHz,but my pc wont boot up,what's the problem?I'm using 533 Micron D9 with 550W pure power supply....Can sifu tell me what's going on?Only 2.7 also cant make it?

RAM multipiler should set 2x
Normally can reach 380 to 400Fsb, more than tht need some luck and increase vCOre
Izzit CM pure power?? Better dont push too far. Tht PSU is not so stable one.

I'm using a 550W pure power PSU,it's taken down from intel big machine,it has 2x12V,(black and yellow),24pins,everything la....and even idle and do nothing (default speed 2.40GHz),it hangs too.....i really dont know what is going on....help me sifu....

Actually 1st thing is we dont recommend u o'c with CM PurePower series.
If small o'c maybe can la..

If lucky then just pc reboot.. if bad luck can spoil your mobo or proc one. Careful

depend on the model i think
last time, me oso 1 of CM 550W PSU user

never caught into problem until i get rid of em' bcoz wanna try another brand of psu